TDA10085 Philips Semiconductors, TDA10085 Datasheet
TDA10085
Available stocks
Related parts for TDA10085
TDA10085 Summary of contents
Page 1
... DATA SHEET TDA10085HT Single chip DVB-S/DSS channel receiver Product specification Supersedes data of 2000 March 16 File under Integrated Circuits, IC02 INTEGRATED CIRCUITS 2001 Aug 31 ...
Page 2
... APPLICATION INFORMATION 11 PACKAGE OUTLINE 12 SOLDERING 12.1 Introduction to soldering surface mount packages 12.2 Reflow soldering 12.3 Wave soldering 12.4 Manual soldering 12.5 Suitability of surface mount IC packages for wave and reflow soldering methods 13 DATA SHEET STATUS 14 DEFINITIONS 15 DISCLAIMERS 16 PURCHASE OF PHILIPS I 2001 Aug COMPONENTS 2 Product specification TDA10085HT ...
Page 3
... Viterbi output and the Reed-Solomon decoder input. The de-interleaver and Reed-Solomon decoder are automatically synchronized according to a frame and 8 synchronization algorithm that uses the sync pattern present in each packet. The TDA10085 is controlled via C-bus interface. The circuit operates at sampling frequencies up to 100 MHz, can process variable 1 ...
Page 4
... DE-INTERLEAVER DECODER DECODER TDA10085HT CONTROL LOGIC DISECQ 22K CTRL1 CTRL2 CTRL3 PLLGND DGDND Fig.1 Block diagram. 4 Product specification TDA10085HT 10 1.0 mm AVD ADVD VDDE 16 42 CARRIER SYNC AGC DETECTION HALF-NYQUIST FILTERS CLOCK SYNC OUTPUT DE-SCRAMBLER INTERFACE BOUNDARY SCAN 9, 25, 39, ...
Page 5
... V); a 0.1 F decoupling capacitor must be placed between AVD and AVS I SADDR0 input signal is the LSB of the I TDA10085; other bits of the address are set internally to 000111, therefore the complete plus the SADDR0 bit; see note 1 I test input; must be connected to ground for normal operation; see ...
Page 6
... I/O boundary scan mode: test data and instruction serial input serial mode enabled (ENSERI = 1): serial TS data output; must be set to VSS when not in serial mode 6 Product specification TDA10085HT DESCRIPTION 2 C-bus; open drain output requiring AGC sampling clock; ...
Page 7
... I asynchronous, active LOW input that clears the TDA10085; when CLB# goes LOW the circuit immediately enters its RESET mode and normal operation resumes three XIN rising edges later after CLB# returns HIGH; at RESET, the I initialized to their default values ...
Page 8
... VDDI 3 PLLVCC 4 PLLGND 5 DGND 6 DVCC 7 VDDI 8 VSSI 9 VDD3 10 AVS 11 VIN2 12 VREFN 13 VREFP 14 VIN1 15 AVD 16 2001 Aug 31 TDA10085HT Fig.2 Pin configuration. 8 Product specification TDA10085HT 48 UNCOR 47 PSYNC 46 CLB# 45 VSSE 44 VDDE 43 ADVS ADVD 42 41 TDO 40 TDI 39 VSSI 38 VDDI 37 FEL 36 TRST 35 TCK 34 TMS 33 SCL ...
Page 9
... TTL input; note 1 TTL input note 4 OH O(max 0 note 4 OL O(max MHz VDDE s symbol rate VDDI 1 Mbaud 27.5 Mbauds 45 Mbauds 9 Product specification TDA10085HT MIN. MAX. 0.5 +4.1 0.5 +2.2 0 0.5 VDDE 0 70 150 300 CONDITIONS VALUE in free air 45 MIN. TYP. MAX. 3.0 3.3 3.6 1.6 1.8 2.0 5.0 5 ...
Page 10
... DO[7:0], DEN, PSYNC, UNCOR, TDI, TDO, TRST, TMS, SDA, SCL_O and SDA_O O(max for pins CTRL1, CTRL2, CTRL3, VAGC and FEL, 22K. O(max) 2001 Aug 31 CONDITIONS MIN. 3.0 3.0 3.0 V VREFN note 2 note 3 10 Product specification TDA10085HT TYP. MAX. UNIT 3.3 3.6 V 3.3 3.6 V 3.3 3 VREFP 750 ...
Page 11
... PHASE SHIFT MIXER The TDA10085 can receive a 4 MHz clock signal delivered by the PLL synthesizer, or can generate the sampling clock from a crystal connected between XIN and XOUT. Bypass capacitors (0.1 F) should be placed close to ADC voltage references VREFP and VREFN. handbook, full pagewidth ...
Page 12
... 2.5 scale (1) ( 0.27 0.18 10.1 10.1 12.15 0.5 0.17 0.12 9.9 9.9 11.85 REFERENCES JEDEC EIAJ MS-026 detail 12.15 0.75 1.0 0.2 0.08 0.1 11.85 0.45 EUROPEAN PROJECTION Product specification TDA10085HT SOT357 (1) ( 1.45 1. 1.05 1.05 0 ISSUE DATE 99-12-27 00-01-19 ...
Page 13
... Use a low voltage ( less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds 300 C. When using a dedicated tool, all other leads can be soldered in one operation within seconds between 270 and 320 C. 13 Product specification TDA10085HT ...
Page 14
... This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Changes will be communicated according to the Customer Product/Process Change Notification (CPCN) procedure SNW-SQ-650A. 14 Product specification TDA10085HT SOLDERING METHOD WAVE REFLOW suitable (2) suitable ...
Page 15
... C COMPONENTS 2 C components conveys a license under the Philips’ system provided the system conforms to the I 15 Product specification TDA10085HT These products are not Philips Semiconductors 2 C patent to use the 2 C specification defined by ...
Page 16
... Philips Semiconductors – a worldwide company Contact information For additional information please visit http://www.semiconductors.philips.com. For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com. © Koninklijke Philips Electronics N.V. 2001 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. ...