MCP602 N/A, MCP602 Datasheet - Page 11

no-image

MCP602

Manufacturer Part Number
MCP602
Description
MCP601-2-3-4
Manufacturer
N/A
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MCP602-E/P
Manufacturer:
MICROCHIP
Quantity:
12 000
Part Number:
MCP602-E/SN
Manufacturer:
MICROCHIP
Quantity:
9 042
Part Number:
MCP602-E/SN
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
MCP602-E/ST
Manufacturer:
MICROCHIP
Quantity:
12 000
Part Number:
MCP602-I/P
Manufacturer:
MICROCHIP
Quantity:
12 000
Part Number:
MCP602-I/P
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
MCP602-I/SN
Manufacturer:
MICROC
Quantity:
940
Part Number:
MCP602-I/SN
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Company:
Part Number:
MCP602-I/SN
Quantity:
200
Part Number:
MCP602-I/ST
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
MCP6021-E/MS
0
Part Number:
MCP6021-I/P
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
MCP6021RT-E/OT
0
3.0
The MCP601/2/3/4 family of operational amplifiers are
fabricated on Microchip’s state-of-the-art CMOS
process. They are unity-gain stable and suitable for a
wide range of general purpose applications.
3.1
The MCP601/2/3/4 amplifier family is designed to not
exhibit phase reversal when the input pins exceed the
supply rails. Figure 2-33 shows an input voltage that
exceeds both supplies with no resulting phase
inversion.
The Common Mode Input Voltage Range (V
includes ground in single supply systems (V
does not include V
input behaves linearly as long as the Common Mode
Input Voltage (V
limits (V
Input voltages that exceed the input voltage range
(V
current to flow into, or out of, the input pins. Current
beyond ±2 mA may cause reliability problems.
Applications that exceed this rating must externally
limit the input current with a resistor (R
Figure 3-1.
FIGURE 3-1:
into an input pin.
3.2
There are two specifications that describe the output
swing capability of the MCP601/2/3/4 family of
operational amplifiers. The first specification, Maximum
Output Voltage Swing, defines the absolute maximum
swing that can be achieved under the specified load
conditions. For instance, the output voltage swings to
within 15 mV of the negative rail with a 25 k
V
limited when the input goes beyond the linear region of
operation.
DD
2003 Microchip Technology Inc.
SS
/2. Figure 2-33 shows how the output voltage is
-0.3V to V
V
SS
R
R
APPLICATIONS INFORMATION
IN
Input
Rail-to-Rail Output
IN
IN
-0.3V to V
DD
(maximum expected V
V
CM
SS
-1.2V at +25°C) can cause excessive
R
) is kept within the specified V
DD
IN
- (minimum expected V
DD
. This means that the amplifier
R
-1.2V at +25°C).
IN
limits the current flow
2 mA
2 mA
MCP60X
IN
IN
) - V
), as shown in
IN
DD
)
SS
load to
), but
CMR
CMR
)
The second specification that describes the output
swing capability of these amplifiers is the Linear Output
Voltage Swing. This specification defines the maximum
output swing that can be achieved while the amplifier is
still operating in its linear region. To verify linear
operation in this range, the large signal, DC Open-Loop
Gain (A
supply rails. The measurement must exceed the
specified gains in the spec table.
3.3
The MCP603 is a single amplifier with Chip Select
(CS). When CS is pulled high, the supply current drops
to -0.7 µA (typ.), which is pulled through the CS pin to
V
a high impedance state. Pulling CS low enables the
amplifier. If the CS pin is left floating, the amplifier may
not operate properly. Figure 1-1 is the Chip Select
timing diagram and shows the output voltage, supply
currents and CS current in response to a CS pulse.
Figure 2-27 shows the measured output voltage
response to a CS pulse.
3.4
Driving large capacitive loads can cause stability
problems for voltage feedback op amps. As the load
capacitance increases, the feedback loop’s phase
margin decreases and the closed-loop bandwidth is
reduced. This produces gain peaking in the frequency
response with overshoot and ringing in the step
response.
When driving large capacitive loads with these op
amps (e.g., > 40 pF when G = +1), a small series
resistor at the output (R
feedback loop’s phase margin (stability) by making the
output load resistive at higher frequencies. The
bandwidth will be generally lower than the bandwidth
with no capacitive load.
FIGURE 3-2:
stabilizes large capacitive loads.
Figure 3-3 gives recommended R
different capacitive loads and gains. The x-axis is the
normalized load capacitance (C
to interpret the plot for arbitrary gains. G
noise gain. For non-inverting gains, G
are equal. For inverting gains, G
(e.g., -1 V/V gives G
SS
. When this happens, the amplifier output is put into
R
OL
MCP603 Chip Select
Capacitive Loads
G
), is measured at points 100 mV inside the
MCP60X
MCP601/2/3/4
N
R
= +2 V/V).
Output resistor R
ISO
F
in Figure 3-2) improves the
L
/G
R
N
ISO
) to make it easier
DS21314E-page 11
ISO
C
N
N
N
L
is the circuit’s
and the gain
ISO
is 1+|Gain|
values for
V
OUT

Related parts for MCP602