TDA8416 Philips Semiconductors, TDA8416 Datasheet
TDA8416
Available stocks
Related parts for TDA8416
TDA8416 Summary of contents
Page 1
... DATA SHEET TDA8416 TV and VTR stereo/dual sound processor with integrated filters and 2 I C-bus control Preliminary specification File under Integrated Circuits, IC02 INTEGRATED CIRCUITS November 1989 ...
Page 2
... The TDA8416 is a processor of stereo/dual language signals (B/G-standard) for stereo sound television receivers and VTRs, using the switched-capacitor technique. The AF signals at the TDA8416 inputs must be “(L R)/2” or “language A” on one channel and “R” or “language B” on the second channel (where L = left and R = right) ...
Page 3
... Philips Semiconductors TV and VTR stereo/dual sound processor with integrated filters and I November 1989 2 C-bus control 3 Preliminary specification TDA8416 ...
Page 4
... Philips Semiconductors TV and VTR stereo/dual sound processor with integrated filters and I November 1989 2 C-bus control Fig.2 Input and output loading diagram. 4 Preliminary specification TDA8416 ...
Page 5
... The output from either filter is converted signal by a peak detector and the necessary hysteresis is performed by a Schmitt-trigger. The resultant DC output signals indicate the status of the transmitter (mono, stereo or dual sound). November 1989 2 C-bus control 2 C-bus) 2 C-bus) 5 Preliminary specification TDA8416 ...
Page 6
... The following actions are carried out by the internal power-on reset when it is active: The AF outputs are muted The identification circuit is deactivated (mono) The control ports (C1 and C2) are set LOW 2 The I C-bus transceiver is initialized November 1989 2 C-bus control E1 0.7(L R) 0.7 0. C-bus. 2 C-bus. 2 C-bus. 6 Preliminary specification TDA8416 E2 E1* 2 E2* ...
Page 7
... The AF outputs are kept in the mute state until the contents of the switch register are changed from (00) hex via the 2 I C-bus The identification circuit is activated The control ports are LOW until the mute and control port register is changed (CR bits 10, 11, 20 and 21) 2 The I C-bus transceiver is activated November 1989 2 C-bus control Fig.3 Mute modes. 7 Preliminary specification TDA8416 ...
Page 8
... C-BUS PROTOCOL OF THE TDA8416 The TDA8416 is controlled by a microcomputer and can be written to or read from via the I The first byte is the address and determines whether the TDA8416 read from (status register) or written to (switch register or mute and port control register). Where: ...
Page 9
... Philips Semiconductors TV and VTR stereo/dual sound processor with integrated filters and I Reading the TDA8416 Reading the TDA8416 means reading the status register and the data stream will have the format as illustrated in Fig.5. Where: start bit S = acknowledge bit A = stop bit P = module address MAD = The second byte, the contents of the status register, is defined by Table 2 ...
Page 10
... I Writing to the TDA8416 Writing to the TDA8416 means, writing to either the switch register or the mute and port control register. Which one addressed is defined by the subaddress (the second byte) as illustrated by Fig.6. The third byte contains the information to be stored in the specified register. ...
Page 11
... TDA8416 (HEX) 0 (00) 0 (10) 0 (10) 0 (2A) 0 (10) 1 (1F) 0 (1C) 1 (13) 0 (12) 0 (18) 0 (1A) 1 (1B) 0 (1E) 0 (70) 1 (7F) 0 (7A) 1 (73) 0 (7C) 0 (72) ...
Page 12
... Supply voltage may be applied only when both pins 5 and 15 are connected to ground. November 1989 2 C-bus control SYMBOL 15- 18- tot amb T stg 12 Preliminary specification TDA8416 MIN. TYP. MAX. 13 500 150 UNIT ...
Page 13
... CLK LOW t HIGH SU; DAT 20-5 V 20-5 13 Preliminary specification TDA8416 MIN. TYP. MAX. 10.8 12 13.2 10 3.25 2 0.7 100 0 0.3 1 0.3 0. 2.0 3.0 UNIT kHz ...
Page 14
... note note note notes note 9 note 6 f note 10 THD C L THD 0. Preliminary specification TDA8416 MIN. TYP. MAX. 0.3 1 0.5 4 150 200 0.7 1 2.5 5.9 6 6.1 8.9 9 9.1 0 400 500 600 49 ...
Page 15
... V RMS kHz. O 11. Test circuit see Fig.7. November 1989 2 C-bus control CONDITIONS SYMBOL note W)/W note OSC V 4 OSC 15 Preliminary specification TDA8416 MIN. TYP. MAX 1.7 100 1.2 j9.3 1.7 UNIT dB dB dBV CCIR dB mV MHz V ...
Page 16
... Philips Semiconductors TV and VTR stereo/dual sound processor with integrated filters and I (1) This potentiometer has to be adjusted to achieve the best stereo separation. (2) Direct connection between pins 5 and 16 is achieved. November 1989 2 C-bus control Fig.7 Application and test circuit. 16 Preliminary specification TDA8416 ...
Page 17
... Philips Semiconductors TV and VTR stereo/dual sound processor with integrated filters and I Voltage input = supply voltage pulse voltage Fig.9 Total harmonic distortion diagram (stereo mode). November 1989 2 C-bus control 50 mV (p-p). Fig.8 Ripple rejection test circuit. 17 Preliminary specification TDA8416 ...
Page 18
... 1.73 0.53 0.36 26.92 6.40 1.30 0.38 0.23 26.54 6.22 0.068 0.021 0.014 1.060 0.25 0.051 0.015 0.009 1.045 0.24 REFERENCES JEDEC EIAJ SC603 18 Preliminary specification 3.60 8.25 10.0 2.54 7.62 3.05 7.80 8.3 0.14 0.32 0.39 0.10 0.30 0.12 0.31 0.33 EUROPEAN PROJECTION TDA8416 SOT146 ( max. 0.254 2.0 0.01 0.078 ISSUE DATE 92-11-17 95-05-24 ...
Page 19
... If the bit temperature is between 300 and 400 C, contact may seconds components conveys a license under the Philips’ system provided the system conforms to the I 19 Preliminary specification TDA8416 ). If the stg max 2 C patent to use the 2 C specification defined by ...