DMC40131 Optrex Corporation, DMC40131 Datasheet
DMC40131
Related parts for DMC40131
DMC40131 Summary of contents
Page 1
... Electrical Specifications...........................................................................3 3. Optical Specifications ..............................................................................6 4. I/O Terminal.............................................................................................8 5. Test..........................................................................................................10 6. Appearance Standards............................................................................11 7. Code System of Production Lot ..........................................................14 8. Applying Precautions .............................................................................14 9. Handling Precautions .............................................................................15 Rev. Date DMC40131* (BA) No.98-0165 First Edition July 3, 1998 Final Revision ******* Table of Contents Revision History Page OPTREX CORPORATION OPTREX Approved by Production Div ...
Page 2
... Viewing Area Outline Dimensions Weight LCD Type Viewing Angle Backlight Drawings DMC40131* (BA) No.98-0165 ： min. 0℃ ～ max. 50℃ ： min. -20℃ ～ max. 60℃ ： 40 characters × 1 lines ： 5 × 11 dots ( 1 character ) ： 152.5 (W) × 16.5 (H) mm ： 182.0 (W) × 33.5 (H) × (11.0) (D) mm ： ...
Page 3
... Input Voltage 2.2.DC Characteristics Parameter Symbol Supply Voltage V (Logic) Supply Voltage V (LCD Drive) High Level Input Voltage Low Level Input Voltage High Level Output Voltage Low Level Output Voltage Supply Current DMC40131* (BA) No.98-0165 Conditions － － － Conditions － ...
Page 4
... Enable Pulse Width Enable Rise/Fall Time Address Setup Time Address Hold Time Write Data Setup Time Write Data Hold Time Read Data Delay Time Read Data Hold Time DB0 ～ DB7 DB0 ～ DB7 DMC40131* (BA) No.98-0165 Symbol Conditions t Fig.1, 2 CYC PW Fig. ...
Page 5
... Please maintain the above sequence when turning on and off the power supply of the module supplied to the module while internal alternate signal for LCD driving (M) is unstable component will be supplied to the LCD panel. This may cause damage the LCD module. DMC40131* (BA) No.98-0165 0 ≦ ≦ ≦ ≦ t ...
Page 6
... D Vth1 : The voltage V measured atθ= 10ﾟ, φ=270ﾟon the segment which the ON signal is applied to. Vth2 : The voltage V measured atθ= 40ﾟ, φ=270ﾟon the segment which the OFF signal is applied to. V O-P DMC40131* (BA) No.98-0165 Symbol Conditions Ta= 0℃ Ta=25℃ Ta=50℃ ...
Page 7
... Duty, 1/4 Bias, V 135ﾟ 180ﾟ 225ﾟ ･Area shows typ. CR≧2 3.4.System Block Diagram Photometer #1980A WB Computer DMC40131* (BA) No.98-0165 f =3.7V, =60Hz D F 90ﾟ 45ﾟ φ (φ= 0ﾟ） ...
Page 8
... DB6 13 DB7 14 4.2.Example of Power Supply It is recommended to apply a potentiometer for the contrast adjust due to the tolerance of the driving voltage and its temperature dependence. DMC40131* (BA) No.98-0165 Level － Power Supply (0V, GND) － Power Supply for Logic － Power Supply for LCD Drive ...
Page 9
... Diagram DB7 DB0 E R/W RS VCC VSS VEE DMC40131* (BA) No.98-0165 COM 11 8 Control LSI SEG 40 HD44780 or equivalent 4 Bias Circuit OPTREX CORPORATION OPTREX characters × 1 lines SEG 160 Column Driver LC7930 × equivalent To LSI Page 9/15 ...
Page 10
... Note 4 : The function test shall be conducted after 4 hours storage at the normal temperature and humidity after removed from the test chamber. Note 5 : Vibration test will be conducted to the product itself without putting container. DMC40131* (BA) No.98-0165 50℃±2℃, 96hrs (operation state) 0℃±2℃, 96hrs (operation state) 60℃ ...
Page 11
... All directions for inspecting the sample should be within 45ﾟagainst perpendicular line. 6.2.Definition of applicable Zones A Zone : Active display area B Zone : Area from outside of "A Zone" to validity viewing area C Zone : Rest parts A Zone + B Zone = Validity viewing area DMC40131* (BA) No.98-0165 45 ﾟ A Zone Bezel Flame B Zone C Zone ...
Page 12
... No. Parameter 1 Black and White Spots, Foreign Substances 2 Air Bubbles (between glass & polarizer) DMC40131* (BA) No.98-0165 Criteria (1) Round Shape Zone Dimension (mm) D ≦ 0.1 0.1 ＜ D ≦ 0.2 0.2 ＜ D ≦ 0.3 0.3 ＜ Long + Short ) / Disregard (2) Line Shape Zone X(mm) Y(mm) － 0.02≧W 2.0≧L 0.03≧W 1.0≧L 0.04≧ ...
Page 13
... No. Parameter 3 The Shape of Dot 4 Polarizer Scratches 5 Polarizer Dirts 6 Color Variation DMC40131* (BA) No.98-0165 Criteria (1) Dot Shape (with Dent) 0.15 ≧ (2) Dot Shape (with Projection) Should not be connected to next dot. (3) Pin Hole X Y Total defects shall not exceed 5. Not to be conspicuous defects. If the stains are removed easily from LCDP surface, the module is not defective ...
Page 14
... System of Production Lot The production lot of module is specified as follows. □ □ 8.Applying Precautions Please contact us when questions and/or new problems not specified in this specifications arise. DMC40131* (BA) No.98-0165 □ □ □ □ Factory Number (Numeral) Factory Code (Alphabet) Production Week (1～5) Production Month (1～ ...
Page 15
... Please consult OPTREX to specify the connection. Optrex shall not be responsible for any infringement of industrial property rights of third parties in any country arising out of the application or use of Optrex Products, except which directly concern the structure or production of such products. DMC40131* (BA) No.98-0165 (GND) is not specified in the module. SS OPTREX CORPORATION ...