UPD16857 NEC, UPD16857 Datasheet
UPD16857
Related parts for UPD16857
UPD16857 Summary of contents
Page 1
... When mounted on a glass epoxy board (10 cm The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. Not all devices/types available in every country. Please check with local NEC representative for availability and additional information. Document No. S13908EJ1V0DS00 (1st edition) ...
Page 2
RECOMMENDED OPERATING CONDITIONS Parameter Symbol Note Control block supply voltage V DD Output block supply voltage V M Output current (pulse) I D(pulse) Operating frequency f IN Operating temperature range T A Peak junction temperature T CH(MAX) Note The low-voltage ...
Page 3
CHARACTERISTICS and the other parameters are within their recommended operating ranges as described above A unless otherwise specified. The parameters other than changes in delay time are when the current is ON. Parameter Symbol (ch1, 3, ...
Page 4
... PIN CONNECTION ch1 10 ch2 ch5 14 15 ch6 Pin No. Pin name Pin function 1 V Control block supply voltage pin DD (3.3 V input ch1 input pin ch1 input pin ch2 input pin ch2 input pin ch1 output pin ...
Page 5
... Bridge (ch5) GND Bridge (ch6) 16 ch5 Control MLD 5A Remark Plural terminal ( GND) is not only 1 terminal and connect all terminals. M MLD LVP ch1 ch3 ch4 Control Control Control level level level ...
Page 6
FUNCTION TABLE V (COMMON) DD IN1A - IN6A IN1B - IN6B SEL GND (COMMON) IN1A - IN6A IN1A - IN6A Don’t care Z: High impedance MLD PGND INPUT OUTPUT ...
Page 7
TYPICAL CHARACTERISTICS P vs. T characteristics T A 1.0 125 C/W 0 100 Ambient temperature vs characteristics 3 1.5 1.0 3.0 3.3 Control block supply voltage ...
Page 8
R vs. T characteristics ON A 3.0 R ONa(ch6) 2.5 R 2.0 1.5 R ONb(ch2 Ambient temperature vs. T characteristics THLa THLb THLc A 250 200 150 t ...
Page 9
T characteristics PHLa, PHLc, A 120 V =3. =12V M 100 80 t PHLa t PHLb Ambient temperature vs. T characteristics PHLa(A ...
Page 10
ABOUT SWITCHING OPERATION When output A is switched as shown in the figure on the right, a dead time (time during which both Pch and Nch are off) elapses to prevent through current. Therefore, the waveform of output A (rise ...
Page 11
... LSI. On the PWB, keep the pattern width of the V insert the bypass capacitors between V Connect a low inductance magnetic capacitor (4700 pF or more) and an electrolytic capacitor so, depending on the load current, in parallel. and GND lines as wide and short as possible, and M and GND at location as close to the LSI as possible ...
Page 12
PACKAGE DIMENSION 38-PIN PLASTIC SSOP (300 mil NOTE Each lead centerline is located within 0. its true position (T.P.) at maximum material condition detail of lead end F 19 ...
Page 13
... Solder this product under the following recommended conditions. For details of the recommended soldering conditions, refer to information document Semiconductor Device Mounting Technology Manual (C10535E). For soldering methods and conditions other than those recommended, consult NEC. Soldering Method Package peak temperature: 235 C; Time: 30 secs. max. (210 C min.); ...
Page 14
Data Sheet S13908EJ1V0DS00 PD16857 ...
Page 15
Data Sheet S13908EJ1V0DS00 PD16857 15 ...
Page 16
... Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance ...