LM3S308 Luminary Micro, Inc, LM3S308 Datasheet - Page 173

no-image

LM3S308

Manufacturer Part Number
LM3S308
Description
Lm3s308 Arm Microcontroller
Manufacturer
Luminary Micro, Inc
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LM3S308
Manufacturer:
DSP
Quantity:
648
Part Number:
LM3S308-EQN25-C2
Manufacturer:
Texas Instruments
Quantity:
10 000
Part Number:
LM3S308-EQN25-C2T
Manufacturer:
Texas Instruments
Quantity:
10 000
Part Number:
LM3S308-IGZ25-C2
Manufacturer:
AV
Quantity:
241
Company:
Part Number:
LM3S308-IGZ25-C2
Quantity:
982
Part Number:
LM3S308-IQN25
Manufacturer:
Texas Instruments
Quantity:
10 000
Part Number:
LM3S308-IQN25-C2
Manufacturer:
TI
Quantity:
202
Part Number:
LM3S308-IQN25-C2
Manufacturer:
Texas Instruments
Quantity:
10 000
Part Number:
LM3S308-IQN25-C2
Manufacturer:
TI/德州仪器
Quantity:
5 288
Part Number:
LM3S308-IQN25-C2T
Manufacturer:
Texas Instruments
Quantity:
10 000
9.3.4
9.3.5
June 04, 2008
In One-Shot mode, the timer stops counting after step 8 on page 172. To re-enable the timer, repeat
the sequence. A timer configured in Periodic mode does not stop counting after it times out.
16-Bit Input Edge Count Mode
A timer is configured to Input Edge Count mode by the following sequence:
1.
2.
3.
4.
5.
6.
7.
8.
9.
In Input Edge Count Mode, the timer stops after the desired number of edge events has been
detected. To re-enable the timer, ensure that the TnEN bit is cleared and repeat step 4 on page 173
through step 9 on page 173.
16-Bit Input Edge Timing Mode
A timer is configured to Input Edge Timing mode by the following sequence:
1.
2.
3.
4.
5.
6.
7.
8.
Ensure the timer is disabled (the TnEN bit is cleared) before making any changes.
Write the GPTM Configuration (GPTMCFG) register with a value of 0x4.
In the GPTM Timer Mode (GPTMTnMR) register, write the TnCMR field to 0x0 and the TnMR
field to 0x3.
Configure the type of event(s) that the timer captures by writing the TnEVENT field of the GPTM
Control (GPTMCTL) register.
Load the timer start value into the GPTM Timern Interval Load (GPTMTnILR) register.
Load the desired event count into the GPTM Timern Match (GPTMTnMATCHR) register.
If interrupts are required, set the CnMIM bit in the GPTM Interrupt Mask (GPTMIMR) register.
Set the TnEN bit in the GPTMCTL register to enable the timer and begin waiting for edge events.
Poll the CnMRIS bit in the GPTMRIS register or wait for the interrupt to be generated (if enabled).
In both cases, the status flags are cleared by writing a 1 to the CnMCINT bit of the GPTM
Interrupt Clear (GPTMICR) register.
Ensure the timer is disabled (the TnEN bit is cleared) before making any changes.
Write the GPTM Configuration (GPTMCFG) register with a value of 0x4.
In the GPTM Timer Mode (GPTMTnMR) register, write the TnCMR field to 0x1 and the TnMR
field to 0x3.
Configure the type of event that the timer captures by writing the TnEVENT field of the GPTM
Control (GPTMCTL) register.
Load the timer start value into the GPTM Timern Interval Load (GPTMTnILR) register.
If interrupts are required, set the CnEIM bit in the GPTM Interrupt Mask (GPTMIMR) register.
Set the TnEN bit in the GPTM Control (GPTMCTL) register to enable the timer and start counting.
Poll the CnERIS bit in the GPTMRIS register or wait for the interrupt to be generated (if enabled).
In both cases, the status flags are cleared by writing a 1 to the CnECINT bit of the GPTM
Preliminary
LM3S308 Microcontroller
173

Related parts for LM3S308