MT28F004B3VG-8BET Micron, MT28F004B3VG-8BET Datasheet - Page 10

• Manufacturer Part Number: MT28F004B3VG-8BET
• Description: 512K x 8 3V only, dula supply, smart 3 boot block flash memory
• Manufacturer: Micron

mand is input on DQ0–DQ7, while DQ8–DQ15 are
“Don’t Care” on the MT28F400B3. The command is
latched on the rising edge of CE# (CE#-controlled) or
WE# (WE#-controlled), whichever occurs first. The con-
dition of BYTE# on the MT28F400B3 has no effect on a
command input.
MEMORY ARRAY
logic 0s but cannot change a given bit to a logic 1 from a
logic 0. Setting any bits to a logic 1 requires that the entire
block be erased. To perform a WRITE, OE# must be HIGH,
CE# and WE# must be LOW, and V
or V
RP# pin be at V
the address to be written, while the data to be written to
the array is input on the DQ pins. The data and addresses
are latched on the rising edge of CE# (CE#-controlled) or
WE# (WE#-controlled), whichever occurs first. A WRITE
must be preceded by a WRITE SETUP command. Details
on how to input data to the array are described in the
Write Sequence section.
4Mb Smart 3 Boot Block Flash Memory
F45_3.p65 – Rev. 3, Pub. 12/01
COMMAND
RESERVED
READ ARRAY
IDENTIFY DEVICE
READ STATUS REGISTER
CLEAR STATUS REGISTER
ERASE SETUP
ERASE CONFIRM/RESUME
WRITE SETUP
ERASE SUSPEND
A WRITE to the memory array sets the desired bits to
PPH
2
. Writing to the boot block also requires that the
HH
or WP# be HIGH. A0–A17/(A18) provide
HEX CODE DESCRIPTION
40h or
PP
D0h
00h
90h
70h
50h
20h
10h
B0h
FFh
must be set to V
The first command given in the two-cycle WRITE sequence. The write
This command and all unlisted commands are invalid and should not
be called. These commands are reserved to allow for future feature
enhancements.
Must be issued after any other command cycle before the array can be
read. It is not necessary to issue this command after power-up or RESET.
Allows the device ID and manufacturer compatibility ID to be read. A0 is
used to decode between the manufacturer compatibility ID (A0 = LOW)
and device ID (A0 = HIGH).
Allows the status register to be read. Please refer to Table 2 for more
information on the status register bits.
Clears status register bits 3-5, which cannot be cleared by the ISM.
The first command given in the two-cycle ERASE sequence. The ERASE is
not completed unless followed by ERASE CONFIRM.
The second command given in the two-cycle ERASE sequence. Must follow
an ERASE SETUP command to be valid. Also used during an ERASE
SUSPEND to resume the ERASE.
data and address are given in the following cycle to complete the WRITE.
Requests a halt of the ERASE and puts the device into the erase suspend
mode. When the device is in this mode, only READ STATUS REGISTER,
READ ARRAY and ERASE RESUME commands may be executed.
Command Set
SMART 3 BOOT BLOCK FLASH MEMORY
PPH
Table 1
1
10
READs on the MT28F400B3. When BYTE# is LOW (byte
mode), data is input on DQ0–DQ7, DQ8–DQ14 are High-
Z and DQ15 becomes the lowest order address input.
When BYTE# is HIGH (word mode), data is input on DQ0–
DQ15.
COMMAND SET
MT28F004B3 and MT28F400B3 incorporate an ISM that
controls all internal algorithms for the WRITE and ERASE
cycles. An 8-bit command set is used to control the de-
vice. Details on how to sequence commands are pro-
vided in the Command Execution section. Table 1 lists
the valid commands.
ISM STATUS REGISTER
check for WRITE or ERASE completion or any related
errors. During or following a WRITE, ERASE or ERASE
SUSPEND, a READ operation outputs the status register
Selectable bus sizing applies to WRITEs as it does to
To simplify writing of the memory blocks, the
The 8-bit ISM status register (see Table 2) is polled to
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2001, Micron Technology, Inc.
4Mb