MT8889CE/CE-1 Mitel Semiconductor, MT8889CE/CE-1 Datasheet - Page 3

no-image

MT8889CE/CE-1

Manufacturer Part Number
MT8889CE/CE-1
Description
6V, 10mA, integrated DTMF transceiver with adaptive micro interface. For paging systems, repeater systems/mobile radio, credit card systems, personal computers, interconnect dialers
Manufacturer
Mitel Semiconductor
Datasheet
Functional Description
The
Transceiver consists of a high performance DTMF
receiver with an internal gain setting amplifier and a
DTMF generator, which employs a burst counter to
synthesize precise tone bursts and pauses. A call
progress mode can be selected so that frequencies
within the specified passband can be detected. The
adaptive micro interface allows microcontrollers,
such as the 68HC11, 80C51 and TMS370C50, to
access the MT8889C/MT8889C-1 internal registers.
Input Configuration
The input arrangement of the MT8889C/MT8889C-1
provides a differential-input operational amplifier as
well as a bias source (V
inputs at V
a feedback resistor to the op-amp output (GS) for
gain adjustment. In a single-ended configuration, the
input pins are connected as shown in Figure 3.
Figure 4 shows the necessary connections for a
differential input configuration.
Receiver Section
Separation of the low and high group tones is
achieved by applying the DTMF signal to the inputs
of two sixth-order switched capacitor bandpass
filters, the bandwidths of which correspond to the low
and high group frequencies (see Table 1). The filters
also incorporate notches at 350 Hz and 440 Hz for
exceptional dial tone rejection. Each filter output is
followed by a single order switched capacitor filter
section, which smooths the signals prior to limiting.
Limiting is performed by high-gain comparators
which are provided with hysteresis to prevent
detection of unwanted low-level signals. The outputs
of the comparators provide full rail logic swings at
the frequencies of the incoming DTMF signals.
Figure 3 - Single-Ended Input Configuration
VOLTAGE GAIN
(A
V
) = R
C
MT8889C/MT8889C-1
F
DD
/ R
/2. Provision is made for connection of
IN
R
IN
Ref
), which is used to bias the
R
F
Integrated
IN+
IN-
GS
V
Ref
MT8889C/
MT8889C-1
DTMF
DIFFERENTIAL INPUT AMPLIFIER
C1 = C2 = 10 nF
R1 = R4 = R5 = 100 k
R2 = 60k , R3 = 37.5 k
R3 = (R2R5)/(R2 + R5)
VOLTAGE GAIN
(A
INPUT IMPEDANCE
(Z
F
697
697
697
770
770
770
852
852
852
941
941
941
697
770
852
941
LOW
IN
V
diff) = 2 R1
diff) - R5/R1
Figure 4 - Differential Input Configuration
Table 1. Functional Encode/Decode Table
C2
C1
1209
1336
1477
1209
1336
1477
1209
1336
1477
1336
1209
1477
1633
1633
1633
1633
0= LOGIC LOW, 1= LOGIC HIGH
F
MT8889C/MT8889C-1
HIGH
R4
R1
2
R3
+ (1/ C)
DIGIT
2
C
D
A
B
1
2
3
4
5
6
7
8
9
0
#
*
R2
R5
D
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
3
D
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
2
IN-
IN+
GS
V
Ref
MT8889C/
MT8889C-1
D
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
D
4-109
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
0

Related parts for MT8889CE/CE-1