TM10032ABC TIANMA, TM10032ABC Datasheet

no-image

TM10032ABC

Manufacturer Part Number
TM10032ABC
Description
LCD_Module
Manufacturer
TIANMA
Datasheet
SPECIFICATION FOR LCD MODULE
TIANMA MICROELECTRONICS CO., LTD
Prepared by:
Checked by :
Verified by :
Approved by:
Model No.
TM10032ABC
Date:
Date:
Date:
Date:

Related parts for TM10032ABC

TM10032ABC Summary of contents

Page 1

... SPECIFICATION FOR LCD MODULE Model No. Prepared by: Checked by : Verified by : Approved by: TIANMA MICROELECTRONICS CO., LTD TM10032ABC Date: Date: Date: Date: ...

Page 2

REVISION RECORD Date Ref. Page Revision No. Revision Items 1/21 Check & Approval ...

Page 3

General Specifications: 1.1 Display type: STN 1 1.2 Display color* : Display color: Blue-Black 2 Background* : Yellow 1.3 Polarizer mode: Transflective/Positive 1.4 Viewing Angle: 6:00 1.5 Driving Method: 1/32 Duty 1/6.7 Bias 1.6 Backlight: LED 1.7 Controller: NJU6450A ...

Page 4

Outline Drawing 3/21 ...

Page 5

... LCD Module Part Numbering System T M 10032 BACKLIGHT TYPE C:LED BACKLIGHT,TRANSFLECTIVE LCD TYPE B: YELLOW-GREEN MODE STN, POSITIVE MODULE SERIES MODULE TYPE 5 DIGITS INDICATING NUMBER 100 COLUMNS X 32 ROWS T: TIANMA M: MODULE 4/21 ...

Page 6

Circuit Block Diagram 5/21 ...

Page 7

Absolute Maximum Ratings Item Power Supply Voltage LCD Driving Voltage Operating Temperature Range Storage Temperature Range Symbol Min. Max -0.3 7 -0.3 13.0 LCD -20 +60 ST 6/21 Unit ...

Page 8

Electrical Specifications and Instruction Code 6.1 Electrical characteristics Item Supply Voltage (Logic) Supply Voltage (LCD Drive) High Input Signal Voltage Low Supply current (Logic) V Supply current (LCD Drive) Supply current (LED) Symbol Min 4 ...

Page 9

Interface Signals Pin No. Symbol Level 1 Vss 2 Vcc 5.0V 3 Vee -3. H/L 5 R DB0 H/L 10 DB1 H/L 11 DB2 H/L 12 DB3 ...

Page 10

Interface Timing Chart AC Characteristics(V System bus read/write I (80 family MPU) A0, WR, RD D0-D7 (WRITE) D0-D7 (READ) Characteristic Address hold time Address setup time System cycle time Control pulse width Data setup time Data hold time RD ...

Page 11

System bus read/write II (68 family MPU) E R/W A0 D0-D7 (WRITE) D0-D7 (READ) Characteristic System cycle time Address setup time Address hold time Data setup time Data hold time Output disable time Access time Read Enable ...

Page 12

Instruction Code Command Display On/Off Display Start Line Page Address Set Column(SEG Address Set Status Read Write Display ...

Page 13

Optical Characteristics 7.1 Optical Characteristics Item Symbol Viewing Angle Contrast Ratio C Turn Response Time Turn T off off Condition = ≥ ...

Page 14

Definition of Optical Characteristics 7.2.1 Definition of Viewing Angle Top Bottom 7.2.2 Definition of Contrast Ratio Contrast Ratio Measuring Conditions: 1) Ambient Temperature: 7.2.3 Definition of Response time t Turn on time Measuring Condition: 1) Operating Voltage: ...

Page 15

Reliability 8.1 Content of Reliability Test No. Test Item High Temperature 1 Storage Low Temperature 2 Storage High Temperature Operation 3 Low Temperature 4 Operation High Temperature /Humidity Storage 5 Temperature Cycle 6 Vibration Test 7 (package state) Shock ...

Page 16

Failure Judgment Criterion Criterion Item Basic Specification Electrical specification Mechanical Specification Optical Characteristic Note For test item refer to 8.1 Remark Basic specification = Optical specification + Mechanical specification Test ...

Page 17

QUALITY LEVEL Examination At Ta=25 or Test (unless otherwise stated) Under normal illumination External and eyesight condition, Visual the distance between eyes Inspection and LCD is 25cm. Under normal illumination Display and eyesight condition, Defects display on inspection. Note: ...

Page 18

Precautions for Use of LCD Modules 10.1 Handling Precautions 10.1.1 The display panel is made of glass. Do not subject mechanical shock by dropping it from a high place, etc. 10.1.2 If the display panel is ...

Page 19

Storage precautions 10.2.1 When storing the LCD modules, avoid exposure to direct sunlight or to the light of fluorescent lamps. 10.2.2 The LCD modules should be stored under the storage temperature range. If the LCD modules will be stored ...

Page 20

Appendix A Inspection items and criteria for appearance defects Items Contents Leakage Rainbow Wrong polarizer attachment Bubble between Polarizer polarizer and glass Scratches of polarizer Black spot (in viewing area) Black line (in viewing area) Progressive cracks Criteria Not permitted ...

Page 21

Appendix B Inspection items and criteria for display defects Items Contents Open segment or open common Short Wrong viewing angle Contrast radio uneven Crosstalk Pin holes and cracks in segment (DOT) Black spot (in viewing area) Black line (in viewing ...

Page 22

     ...

Related keywords