stf28-461 Interpoint Corp., stf28-461 Datasheet
stf28-461
Related parts for stf28-461
stf28-461 Summary of contents
Page 1
... Compatible with MIL-STD-704 A-E 28 VDC power bus DESCRIPTION The STF28-461™ EMI filter module has been designed as a companion for Interpoint SMSA flyback power converters. Multiple SMSA power converters can be operated from a single filter provided the total power line current does not exceed the filter maximum rating. The STF filter will reduce the SMSA’ ...
Page 2
... Common The case ground connection between the filter and the converter should be as low an impe ance as possible to minimize EMI. Direct contact of baseplate to chassis ground provides the www.craneae.com STF28-461 EMI Input Filters 28 VOlT INPuT – 0.8 aMP meChaniCal and envirOnmental Size (maximum) 0.980 x 0.805 x 0.270 (24.89 x 20.45 x 6.86 mm) See case A1 for dimensions ...
Page 3
... STF28-461 EMI Input Filters 28 VOlT INPuT – 0.8 aMP pin OUt Pin Designation 1 Positive Input 2, 3 Positive Output 4 Case Ground 5, 6 Output Common 7 Input Common 8 Case Ground Squared corner and dot on top of cover indicate pin one BOTTOM 8 4 VIEW STF ...
Page 4
... Choose one from each of the following rows Screening * Interpoint model numbers use an “O” in the RHA designator position to indicate the “-” (dash) Radiation Hardness Assurance level of MIL-PRF-38534, which is defined as “no RHA” www.craneae.com STF28-461 EMI Input Filters 28 VOlT INPuT – 0.8 aMP / KH mOdel seleCtiOn 461 ...
Page 5
... VOltage input Current nOiSe reJeCtiOn DC reSiStanCe (r Output VOltage Output Current pOwer DiSSipatiOn at maXimum Current Notes: 1. Guaranteed by design, not tested. www.craneae.com STF28-461 EMI Input Filters 28 VOlT INPuT – 0.8 aMP COnDitiOnS min COntinuOuS 0 1 — 500 kHz MHz MHz ...
Page 6
... Typical Performance Curves: 25°C Tc, nominal Vin, unless otherwise specified. www.craneae.com STF28-461 EMI Input Filters 28 VOlT INPuT – 0.8 aMP NARROWBAND .015 0 FREQUENCY (MHz) MSA2805S converter without a filter igure NARROWBAND .015 0 FREQUENCY (MHz) MSA2805S converter at full load with an STF28-461 EMI filter. ...
Page 7
... STF28-461 EMI Input Filter Cases Projection Weld Seam Seal Seal hole: 0.056 ±0.002 (1.42 ±0.05) Case dimensions in inches (mm) Tolerance ±0.005 (0.13) for three decimal places ±0.01 (0.3) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. ...
Page 8
... Not applicable to EMI filters that have no wirebonds. Definitions: Element Evaluation: Component testing/screening per MIL-STD-883 as determined by MIL-PRF-38534 SEM: Scanning Electron Microscopy SLAM™: Scanning Laser Acoustic Microscopy C-SAM Mode Scanning Acoustic Microscopy www.craneae.com STF28-461 EMI Input Filters 28 VOlT INPuT – 0.8 aMP K, MIl-PRF-38534 E s PaCE P o ...
Page 9
... Test methods are referenced to MIL-STD-883 as determined by MIL-PRF-38534. Notes: 1. Space Prototype (O), non-QML products, do not meet all of the requirements of MIL-PRF-38534. 2. Not applicable to EMI filters that have no wirebonds. 3. Not required by DSCC but performed to assure product quality. www.craneae.com STF28-461 EMI Input Filters 28 VOlT INPuT – 0.8 aMP P RototyPE non 2 ...
Page 10
... STF EMI Input Filters, Rev A - 20070509. This revision supercedes all previous releases. All technical information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. STF Series is a trademark of Interpoint. Copyright © 1999 - 2007 Interpoint Corporation. All rights reserved. www.craneae.com STF28-461 EMI Input Filters 28 VOlT INPuT – 0.8 aMP K, MIl-PRF-38534 R ...