ir1150s International Rectifier Corp., ir1150s Datasheet
ir1150s
Available stocks
Related parts for ir1150s
ir1150s Summary of contents
Page 1
... Internally clamped 13V gate drive Fast 1.5A peak gate drive Micropower startup (<200 A) Latch immunity and ESD protection Parts also available Lead-Free IR1150 1 8 COM GATE 2 7 FREQ VCC 3 6 ISNS VFB 4 5 OVP COMP + IR1150S(PbF) IR1150IS(PbF) Package 8-Lead SOIC V OUT + RTN 1 ...
Page 2
... — -25 — — 200 SW =15V is assumed for test condition CC Min. Typ. Max. 12.2 12.7 13.2 10.2 10.7 11.2 1.8 — 2.2 Not internally clamped SOIC-8 o SOIC AMB Human body model* Units Remarks V °C °C IR1150S °C IR1150IS kHz Units Remarks ...
Page 3
... Open loop protection (OLP) Vfb threshold Output under voltage protection (OUV) Output over voltage protection (OVP) OVP hysteresis Peak current limit protection ( voltage threshold V PKLMT SNS www.irf.com IR1150S/IR1150IS(PbF) =15V is assumed for test condition. CC Min. Typ. Max. — — — — ...
Page 4
... COMP COMP START Current Amplifier Section Parameters Symbols DC gain Corner frequency Input offset voltage I bias current SNS Input offset voltage temp coefficient Common mode rejection ratio Blanking time T BLANK www.irf.com IR1150S/IR1150IS(PbF) Min. Typ. Max. V 6.9 7.0 7.1 REF — REG T — 0.4 — STAB V 6.8 — ...
Page 5
... Gate Driver Section Parameters Symbols Gate low voltage V Gate high voltage V Gate high voltage V Rise time Fall time Out peak current I Gate voltage @ fault V www.irf.com IR1150S/IR1150IS(PbF) Min. Typ. Max. — 1.2 1.5 GLO — GTH 9.5 — — GTH — 20 — — ...
Page 6
... FB 5 COMP FAULT FAULT PROTECTION OPEN LOOP PROTECTION OUTPUT UNDER VOLTAGE Lead Assignments & Definitions Lead Assignment IR1150S 1 COM 2 FREQ I 3 SNS OVP/ LEAD SOIC www.irf.com IR1150S/IR1150IS(PbF) 1.0V DUTY CYCLE - + RESET FAULT Pin# Symbol 1 COM 2 FREQ 8 GATE I 3 SNS OVP/EN ...
Page 7
... The IC is designed for robust operation and pro- vides protection from system level over current, over voltage, under voltage, and brownout conditions. www.irf.com IR1150S/IR1150IS(PbF) IC Supply The UVLO circuit monitors the V CC the gate drive signal inactive until the V ...
Page 8
... To prevent noise problems, a bypass ceramic capacitor connected to V and COM should be CC placed as close as possible to the IR1150S. This pin is not internally clamped, therefore damage will occur if the maximum voltage is exceeded. OVP/EN: Over Voltage Protection / Enable This pin is the input to the over voltage protection comparator the threshold of which is internally pro- grammed to 105 ...
Page 9
... This controlled duty cycle reduces system component stress during start up conditions as the input current amplitude is increasing linearly. www.irf.com IR1150S/IR1150IS(PbF) Normal Mode The IC enters normal operating mode once the soft turn on threshold start transition has been completed. At this point the ...
Page 10
... LIMIT FAULT V ISNS V < -1.0V ISNS Present PulseTerminated V ISNS Oscillator Active V < ISNS V ISNS V < 0.7V OVP www.irf.com IR1150S/IR1150IS(PbF) AC POWER ON Gate Inactive Oscillator Inactive UVLO V < V CCon CC Gate Inactive Oscillator Inactive I = 200uA CC MAX V > CCon V < UVLO STAND - BY V > 0.7V ...
Page 11
... Programming Resistor Fig Oscillator Frequency vs. Programming Resistor www.irf.com IR1150S/IR1150IS(PbF -50 ° Fig Under Voltage Lockout vs. 250 kHz 200 kHz 150 kHz 100 kHz ...
Page 12
... Temperature Fig Reference Voltage -50 °C 0 °C 50 °C Temperature Fig.7 - Voltage Error Amplifier Source/Sink Current www.irf.com IR1150S/IR1150IS(PbF 100 °C 150 °C -50 °C Fig Voltage Error Amplifier 2.70 2.60 2.50 IO (source) IO (sink) 2.40 2.30 100 °C 150 ° ...
Page 13
... Vcc UVLO 82% V REF OLP SOFT START www.irf.com IR1150S/IR1150IS(PbF) IR1150 Timing Diagrams NORMAL V Under Voltage Lockout cc NORMAL OVP Output Protection 13.0V (typ) 11.0V (typ) t UVLO 106% V REF 100% V REF 51% V REF 19% V REF t OLP OUV 13 ...
Page 14
... 0.25 [.010 NOTES: 1. DIMENSIONING & TOLERANCING PER ASME Y14.5M-1994. 2. CONTROLLING DIMENSION: MILLIMETER 3. DIMENSIONS ARE SHOWN IN MILLIMETERS [INC HES]. 4. OUTLINE CONFORMS TO JEDEC OUTLINE MS-012AA. www.irf.com IR1150S/IR1150IS(PbF) FOOTPRINT 8X 0.72 [.028 6.46 [.255] 3X 1.27 [.050] 8X 1.78 [.070 45° 0.10 [.004 DIMENSION DOES NOT INCLUDE MOLD PROTRUSIONS. ...
Page 15
... Tape & Reel Information Dimensions are shown in millimeters (inches) 8.1 ( .318 ) 7.9 ( .312 ) NOTES: 1. OUTLINE CONFORMS TO EIA-481 & EIA-541. 2. CONTROLLING DIMENSION : MILLIMETER. NOTES : 1. CONTROLLING DIMENSION : MILLIMETER. 2. OUTLINE CONFORMS TO EIA-481 & EIA-541. www.irf.com IR1150S/IR1150IS(PbF) TERMINAL NUMBER 1 330.00 (12.992) MAX. 12.3 ( .484 ) 11.7 ( .461 ) FEED DIRECTION 14.40 ( .566 ) 12.40 ( .488 ) 15 ...
Page 16
... Lead-free Part 8-Lead SOIC IR1150S order IR1150STRPbF 8-Lead SOIC IR1150ISTR order IR1150ISTRPbF The IR1150S(PbF) has been designed and qualified for the Consumer Market The IR1150IS(PbF) has been designed and qualified for the Industrial Market Qualification Standards can be found on IR’s Web site. ...