st62t25c STMicroelectronics, st62t25c Datasheet - Page 41

no-image

st62t25c

Manufacturer Part Number
st62t25c
Description
8-bit Otp/eprom Mcus With A/d Converter, Oscillator Safeguard, Safe Reset And 28 Pins
Manufacturer
STMicroelectronics
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
st62t25c3
Manufacturer:
TOSHIBA
Quantity:
19
Part Number:
st62t25c3
Manufacturer:
ST
0
Part Number:
st62t25c6
Manufacturer:
ST
Quantity:
15 700
Part Number:
st62t25c6
Manufacturer:
ST
Quantity:
1 899
Part Number:
st62t25c6
Manufacturer:
ST
0
Part Number:
st62t25c6
Manufacturer:
ST
Quantity:
20 000
Part Number:
st62t25c6(CM6)
Manufacturer:
ST
Quantity:
20 000
Part Number:
st62t25c6TR
Manufacturer:
ST
0
Part Number:
st62t25cB6
Manufacturer:
ST
Quantity:
310
Part Number:
st62t25cB6
Manufacturer:
STMicroelectronics
Quantity:
5
Part Number:
st62t25cB6
Manufacturer:
ST
0
Part Number:
st62t25cG
Manufacturer:
ST
Quantity:
5 510
Part Number:
st62t25cM6
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
st62t25cM6
Quantity:
1 100
A/D CONVERTER (Cont’d)
Since the ADC is on the same chip as the micro-
processor, the user should not switch heavily load-
ed output signals during conversion, if high preci-
sion is required. Such switching will affect the sup-
ply voltages used as analog references.
The accuracy of the conversion depends on the
quality of the power supplies (V
user must take special care to ensure a well regu-
lated reference voltage is present on the V
V
less than 5V/ms). This implies, in particular, that a
suitable decoupling capacitor is used at the V
pin.
The converter resolution is given by::
The Input voltage (Ain) which is to be converted
must be constant for 1 s before conversion and
remain constant during conversion.
Conversion resolution can be improved if the pow-
er supply voltage (V
lowered.
In order to optimise conversion resolution, the user
can configure the microcontroller in WAIT mode,
because this mode minimises noise disturbances
and power supply variations due to output switch-
ing. Nevertheless, the WAIT instruction should be
executed as soon as possible after the beginning
of the conversion, because execution of the WAIT
instruction may cause a small variation of the V
voltage. The negative effect of this variation is min-
imized at the beginning of the conversion when the
converter is less sensitive, rather than at the end
of conversion, when the less significant bits are
determined.
The best configuration, from an accuracy stand-
point, is WAIT mode with the Timer stopped. In-
deed, only the ADC peripheral and the oscillator
are then still working. The MCU must be woken up
from WAIT mode by the ADC interrupt at the end
of the conversion. It should be noted that waking
SS
pins (power supply voltage variations must be
V
--------- ----- ---- ----------
DD
DD
256
) to the microcontroller is
V
SS
DD
and V
SS
DD
). The
and
DD
DD
up the microcontroller could also be done using
the Timer interrupt, but in this case the Timer will
be working and the resulting noise could affect
conversion accuracy.
A/D Converter Control Register (ADCR)
Address: 0D1h — Read/Write
Bit 7 = EAI: Enable A/D Interrupt. If this bit is set to
“1” the A/D interrupt is enabled, when EAI=0 the
interrupt is disabled.
Bit 6 = EOC: End of conversion. Read Only . This
read only bit indicates when a conversion has
been completed. This bit is automatically reset to
“0” when the STA bit is written. If the user is using
the interrupt option then this bit can be used as an
interrupt pending bit. Data in the data conversion
register are valid only when this bit is set to “1”.
Bit 5 = STA : Start of Conversion. Write Only . Writ-
ing a “1” to this bit will start a conversion on the se-
lected channel and automatically reset to “0” the
EOC bit. If the bit is set again when a conversion is
in progress, the present conversion is stopped and
a new one will take place. This bit is write only, any
attempt to read it will show a logical zero.
Bit 4 = PDS : Power Down Selection. This bit acti-
vates the A/D converter if set to “1”. Writing a “0” to
this bit will put the ADC in power down mode (idle
mode).
Bit 3-0 = D3-D0. Not used
A/D Converter Data Register (ADR)
Address: 0D0h — Read only
Bit 7-0 = D7-D0 : 8 Bit A/D Conversion Result.
EAI
D7
7
7
EOC
D6
STA
D5
PDS
D4
ST62T15C/T25C/E25C
D3
D3
D2
D2
D1
D1
41/70
D0
D0
0
0
41

Related parts for st62t25c