ns2l095at NICHIA CORPORATION, ns2l095at Datasheet
ns2l095at
Related parts for ns2l095at
ns2l095at Summary of contents
Page 1
... SPECIFICATIONS FOR NICHIA CHIP TYPE WARM WHITE LED MODEL : NICHIA CORPORATION NS2L095AT -0- Nichia STS-DA1-0039 <Cat.No.071122> ...
Page 2
Absolute Maximum Ratings Item Forward Current Pulse Forward Current Allowable Reverse Current Power Dissipation Operating Temperature Storage Temperature Dice Temperature Soldering Temperature I Conditions : Pulse Width FP (2) Initial Electrical/Optical Characteristics Item Forward Voltage Luminous Flux Chromaticity ...
Page 3
Rank f3 x 0.4255 0.4390 0.4680 0.4519 y 0.4000 0.4310 0.4385 0.4086 Rank f5 x 0.4129 0.4255 0.4519 0.4355 y 0.3725 0.4000 0.4086 0.3785 Color Coordinates ...
Page 4
The LEDs are packed in cardboard boxes after taping. Please refer to figure’s page. The label on the minimum packing unit shows ; Part Number, Lot Number, Ranking, Quantity · In order to protect the LEDs from mechanical ...
Page 5
TEST ITEMS AND RESULTS Standard Test Item Test Method Resistance to JEITA ED-4701 Soldering Heat (Reflow Soldering) Solderability JEITA ED-4701 (Reflow Soldering) Temperature Cycle JEITA ED-4701 Moisture Resistance Cyclic JEITA ED-4701 High Temperature Storage JEITA ED-4701 Temperature Humidity ...
Page 6
The LEDs are devices which are materialized by combining Blue LEDs and special phosphors. Consequently, the color of the LEDs is changed a little by an operating current. Care should be taken after due consideration when using LEDs. (1) ...
Page 7
Static Electricity · Static electricity or surge voltage damages the LEDs recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs. · All devices, equipment and machinery must be properly grounded. It ...
Page 8
Application Design Considerations · In designing a circuit, the current through each LED must not exceed its absolute maximum rating recommended to use Circuit B which regulates the current flowing through each LED. In the meanwhile, when ...
Page 9
Warpage of circuit board with soldered LEDs may result in damage or package breakage of the LEDs. Please pay special attention to the orientation of the LEDs as to avoid LED failure caused by bow, twist and warpage of ...
Page 10
Handling Precautions · Bare Hand When handling the product, touching encapsulant with bare hands will contaminate its surface that could affects on optical characteristics. In the worst cases, excessive force to the encapsulant by hands might result in catastrophic ...
Page 11
Printed Circuit Board Assembled (PCB with LEDs soldered) Do not stack assembled PCBs together. Since silicone is a soft material, abrasion between two PCB assembled with silicone encapsulated LED might cause catastrophic failure of the LEDs due to damage ...
Page 12
Soldering Conditions · The LEDs can be soldered in place using the reflow soldering method. guarantee on the LEDs after they have been assembled using the dip soldering method. · Recommended soldering conditions Reflow Soldering Lead Solder Pre-heat 120 ...
Page 13
Cleaning · recommended that isopropyl alcohol be used as a solvent for cleaning the LEDs. other solvents, it should be confirmed beforehand whether the solvents will dissolve the package and the resin or not. Freon solvents should ...
Page 14
Color Coordinates Measurement allowance is ± 0.01. ICI Chromaticity Diagram 550 560 570 580 ...
Page 15
... Duty Ratio (%) FP Ambient Temperature vs. Allowable Forward Current 200 I =60mA FP 150 120 110 50 Thermal resistance Rja=110°C 100 Ambient Temperature Ta (°C ) Model NICHIA CORPORATION Title No. Ta=25° 100 60 80 100 NS2L095A CHARACTERISTICS 071016701681 ...
Page 16
... Ambient Temperature vs. Directivity Chromaticity Coordinate 1.0 0.43 I =60mA FP 0.42 -30°C 0°C 25°C 0.5 0.41 50°C 85°C 0.40 0 0.39 0.43 0.44 0.45 0.46 0.47 90° x NICHIA CORPORATION Ta=25°C I =60mA F 500 600 700 800 Wavelength λ (nm) 0° 10° 20° 30° X 40° 50° 60° Ta=25°C 70° I =60mA FP X-X Y-Y 60° 30° 0° 0.5 1 ...
Page 17
... Cathode mark ITEM PACKAGE ENCAPSULATING RESIN Silicone Resin (with Phosphor) ELECTRODES 0.15 MATERIALS Ceramics Ag Plating NICHIA CORPORATION 2.8 0.8 Anode Cathode A K Protection device NS2L095A Model OUTLINE DIMENSIONS Title 070903770451 No. Unit mm 10/1 Scale Allow ±0.1 ...
Page 18
... XXXX LED φ TYPE NS2x095AT LOT xxxxxx- QTY pcs RoHS LEDs mounting part No LEDs Reel Lead Min.100mm (No LEDs) NICHIA CORPORATION 11.4 ±1 φ 180 +0 9 ±0 Pull direction Top cover tape Embossed carrier tape Reel Lead Min.400mm NS2x095AT Model TAPING DIMENSIONS ...
Page 19
... OKA, KAMINAKA, ANAN, TOKUSHIMA, The box is partitioned with the cardboard. Label XXXX LED TYPE NS2x095AT RANK RoHS QTY PCS NICHIA CORPORATION JAPAN 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, Quantity/box (pcs) 21,000 MAX. 45,000 MAX. 90,000 MAX. NS2x095AT PACKING 070905770511 ...