ics426 Integrated Device Technology, ics426 Datasheet

no-image

ics426

Manufacturer Part Number
ics426
Description
Serial Ata/fiber Channel Clock Synthesizer
Manufacturer
Integrated Device Technology
Datasheet
SERIAL ATA/FIBER CHANNEL CLOCK SYNTHESIZER
IDT™ / ICS™ SERIAL ATA/FIBER CHANNEL CLOCK SYNTHESIZER
Description
The ICS426 was developed for serial ATA (SATA) and
fiber channel. It generates a high quality, high
frequency clock output from a low cost frequency
crystal or clock input.
Using Phase-Locked-Loop (PLL) techniques, the
device runs from a standard fundamental mode,
inexpensive crystal or clock input.
Block Diagram
required with a crystal input.
25 MHz
Crystal or
Clock Input
Capacitors may be
S0:S1
X2
X1
Oscillator
Crystal
1
Features
PLL /Clock
Synthesis
Circuitry
Packaged in 16 pin TSSOP
Input crystal or clock frequency of 25 MHz (typical)
Supports serial ATA Generation 1
Supports Fiber Channel
Duty cycle of 45/55
Operating voltage of 3.3V
Advanced, low power, CMOS process
GND
VDD
4
6
OE
ICS426
DATASHEET
ICS426
REV B 091102
CLK

Related parts for ics426

ics426 Summary of contents

Page 1

... SERIAL ATA/FIBER CHANNEL CLOCK SYNTHESIZER Description The ICS426 was developed for serial ATA (SATA) and fiber channel. It generates a high quality, high frequency clock output from a low cost frequency crystal or clock input. Using Phase-Locked-Loop (PLL) techniques, the device runs from a standard fundamental mode, inexpensive crystal or clock input ...

Page 2

... Output Enable. All outputs are tri-stated when low. Internal pull-up. Connect to ground. Power Power Connect to ground. XO Crystal connection. Connect MHz fundamental mode crystal or float for clock input. 2 CLOCK SYNTHESIZER Input CLK Output 150 1 25 106. 156.25 1 Pin Description ICS426 REV B 091102 ...

Page 3

... An optimum layout is one with all components on the same side of the board, minimizing vias through other signal layers. Other signal traces should be routed away from the ICS426. This includes signal traces just underneath the device layers adjacent to the ground plane layer used by the device. ...

Page 4

... Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the ICS426. These ratings, which are standard values for ICS commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied ...

Page 5

... Min. Typ. Max. 0 +70 +3.13 +3.3 +3.46 Min. Typ. Max. 3.13 3.3 3. 0.8 VDD-0.4 2.4 0.4 ±50 150 5 Min. Typ. Max ±70 170 -90 -115 -121 -116 ICS426 Units C V Units Units MHz % dBc/Hz dBc/Hz dBc/Hz dBc/Hz REV B 091102 ...

Page 6

... Min 0.05 0.15 0.002 A2 0.80 1.05 0.032 b 0.19 0.30 0.007 C 0.09 0.20 0.0035 D 4.90 5.1 0.193 E 6.40 BASIC 0.252 BASIC E1 4.30 4.50 0.169 e 0.65 Basic 0.0256 Basic L 0.45 0.75 0.018 aaa -- 0. Package Temperature 16 pin TSSOP 16 pin TSSOP ICS426 Inches Max 0.047 0.006 0.041 0.012 0.008 0.201 0.177 0.030 8 0.004 + +70 C REV B 091102 ...

Page 7

... ICS426 SERIAL ATA/FIBER CHANNEL CLOCK SYNTHESIZER Innovate with IDT and accelerate your future networks. Contact: www.IDT.com For Sales 800-345-7015 408-284-8200 Fax: 408-284-2775 Corporate Headquarters Integrated Device Technology, Inc. 6024 Silver Creek Valley Road San Jose, CA 95138 United States 800 345 7015 +408 284 8200 (outside U.S.) © ...

Related keywords