tda7052at-n2 NXP Semiconductors, tda7052at-n2 Datasheet
tda7052at-n2
Related parts for tda7052at-n2
tda7052at-n2 Summary of contents
Page 1
DATA SHEET TDA7052A/ BTL mono audio amplifier with DC volume control Product specification File under Integrated circuits, IC01 INTEGRATED CIRCUITS July 1994 ...
Page 2
... TDA7052A TDA7052AT ORDERING INFORMATION EXTENDED TYPE NUMBER PINS TDA7052A 8 TDA7052AT 8 Notes 1. SOT97-1; 1996 September 10. 2. SOT96-1; 1996 September 10. July 1994 GENERAL DESCRIPTION The TDA7052A/AT are mono BTL output amplifiers with DC volume control. They are designed for use in TV and monitors, but also suitable for battery-fed portable recorders and radios ...
Page 3
... I – i STABILIZER TEMPERATURE PROTECTION V ref Fig.1 Block diagram. DESCRIPTION handbook, halfpage 3 Product specification TDA7052A/AT 5 positive output 8 negative output 3 6 MCD385 - 1 signal power ground ground OUT – n.c. TDA7052A TDA7052AT GND1 3 6 GND2 OUT + MCD384 Fig.2 Pin configuration. ...
Page 4
... SYMBOL PARAMETER V supply voltage range P I repetitive peak output current ORM I non-repetitive peak output current OSM P total power dissipation tot TDA7052A TDA7052AT T operating ambient temperature range amb T storage temperature range stg T virtual junction temperature vj T short-circuit time sc V input voltage pin 2 ...
Page 5
... TDA7052A TDA7052AT Notes to the thermal resistance TDA7052A The maximum sine-wave dissipation is 0 Therefore T = 150 100 amb(max) TDA7052AT The maximum sine-wave dissipation is 0. Therefore T = 150 155 amb(max) July 1994 PARAMETER 0 0. Product specifi ...
Page 6
... The noise output voltage (RMS value 500 kHz is measured with R 3. The ripple rejection is measured with R is applied to the positive supply rail. 4. The noise output voltage (RMS value) is measured with R July 1994 = 8 ; TDA7052AT unless otherwise specified (see Fig.6 CONDITIONS ...
Page 7
Philips Semiconductors 1 W BTL mono audio amplifier with DC volume control 40 handbook, halfpage gain (dB – 20 – 40 – 60 – 0.4 0.8 1.2 Fig.3 Gain control as a function of DC volume ...
Page 8
... This capacitor can be omitted if the 220 F electrolytic capacitor is connected close to pin 1. handbook, halfpage volume control Fig.7 Application with potentiometer as volume control; maximum gain = 30 dB. July 1994 TDA7052A TDA7052AT STABILIZER TEMPERATURE PROTECTION V ref Fig.6 Test and application diagram. 4 MCD387 8 TDA7052A/AT ...
Page 9
Philips Semiconductors 1 W BTL mono audio amplifier with DC volume control PACKAGE OUTLINES DIP8: plastic dual in-line package; 8 leads (300 mil pin 1 index 1 DIMENSIONS (inch dimensions are derived from the original mm dimensions) ...
Page 10
Philips Semiconductors 1 W BTL mono audio amplifier with DC volume control SO8: plastic small outline package; 8 leads; body width 3 pin 1 index 1 e DIMENSIONS (inch dimensions are derived from the original mm ...
Page 11
Philips Semiconductors 1 W BTL mono audio amplifier with DC volume control SOLDERING Introduction There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on ...
Page 12
Philips Semiconductors 1 W BTL mono audio amplifier with DC volume control DEFINITIONS Data sheet status Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may ...