dac124s085eb National Semiconductor Corporation, dac124s085eb Datasheet
dac124s085eb
Related parts for dac124s085eb
dac124s085eb Summary of contents
Page 1
... DAC084S085 and the 10-bit DAC104S085. The DAC124S085 operates over the extended industrial tem- perature range of −40°C to +105°C. Pin Configuration SPI ™ trademark of Motorola, Inc. © 2007 National Semiconductor Corporation Features ■ Guaranteed Monotonicity ■ Low Power Operation ■ ...
Page 2
Ordering Information Order Numbers DAC124S085CISD DAC124S085CISDX DAC124S085CIMM DAC124S085CIMMX DAC124S085EVAL Block Diagram www.national.com Temperature Range ≤ ≤ −40°C T +105°C A ≤ ≤ LLP Tape-and-Reel −40°C T +105°C A ≤ ≤ −40°C T +105°C A ≤ ≤ MSOP Tape-and-Reel −40°C T ...
Page 3
Pin Descriptions LLP MSOP Symbol Pin No OUTA V 3 OUTB V 4 OUTC 5 V OUTD 6 GND 7 V REFIN SYNC 10 SCLK PAD 11 (LLP only) Type Supply ...
Page 4
Absolute Maximum Ratings If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage Voltage on any Input Pin Input Current at Any Pin (Note 3) Package Input Current ...
Page 5
Symbol Parameter I Output Short Circuit Current (sink) OS Continuous Output I O Current (Note 10) C Maximum Load Capacitance Output Impedance OUT REFERENCE INPUT CHARACTERISTICS Input Range Minimum Input Range Maximum VREFIN Input Impedance LOGIC INPUT ...
Page 6
A.C. and Timing Characteristics Values shown in this table are design targets and are subject to change before product release. The following specifications apply for 4047. Boldface limits apply for T Symbol Parameter f SCLK Frequency SCLK ...
Page 7
Note 9: Typical figures are 25°C, and represent most likely parametric norms. Test limits are guaranteed to National's AOQL (Average Outgoing Quality J Level). Note 10: This parameter is guaranteed by design and/or characterization and is not ...
Page 8
Transfer Characteristic Timing Diagrams www.national.com FIGURE 1. Input / Output Transfer Characteristic FIGURE 2. Serial Timing Diagram 8 20173205 20173206 ...
Page 9
Typical Performance Characteristics 4047, unless otherwise stated INL 3.0V A DNL 3.0V A INL/DNL REFIN REF A SCLK 20173252 20173254 = 3.0V A 20173256 9 ...
Page 10
INL/DNL SCLK INL/DNL vs Clock Duty Cycle at V INL/DNL vs Temperature at V www.national.com = 2.7V A 20173250 = 3.0V INL/DNL vs Clock Duty Cycle 20173224 = 3.0V INL/DNL vs Temperature at ...
Page 11
Zero Code Error vs 20173230 Zero Code Error vs. f SCLK 20173234 Zero Code Error vs. Temperature 20173236 Zero Code Error vs. V Zero Code Error vs. Clock Duty Cycle Full-Scale Error vs REFIN 20173231 20173235 ...
Page 12
Full-Scale Error vs. V Full-Scale Error vs. Clock Duty Cycle Supply Current vs. V www.national.com REFIN 20173232 Full-Scale Error vs. Temperature 20173238 Supply Current vs. Temperature A 20173244 12 Full-Scale Error vs. f SCLK 20173233 20173239 20173245 ...
Page 13
Glitch Response 20173246 Power-On Reset 13 20173247 www.national.com ...
Page 14
Functional Description 1.1 DAC SECTION The DAC124S085 is fabricated on a CMOS process with an architecture that consists of switches and resistor strings that are followed by an output buffer. The reference voltage is ex- ternally applied at V ...
Page 15
POWER-DOWN MODES The DAC124S085 has four power-down modes, two of which are identical. In power-down mode, the supply current drops to 20 µ and 30 µA at 5V. The DAC124S085 is set in power-down mode by setting ...
Page 16
LP3985 The LP3985 is a low noise, ultra low dropout voltage regulator with a 3% accuracy over temperature good choice for applications that do not require a precision reference for the DAC124S085. It comes in 3.0V, ...
Page 17
DSP/MICROPROCESSOR INTERFACING Interfacing the DAC124S085 to microprocessors and DSPs is quite simple. The following guidelines are offered to hasten the design process. 2.3.1 ADSP-2101/ADSP2103 Interfacing Figure 10 shows a serial interface between the DAC124S085 and the ADSP-2101/ADSP2103. The DSP ...
Page 18
Physical Dimensions www.national.com inches (millimeters) unless otherwise noted 10-Lead MSOP Order Numbers DAC124S085CIMM NS Package Number MUB10A 10-Lead LLP Order Numbers DAC124S085CISD NS Package Number SDA10A 18 ...
Page 19
Notes 19 www.national.com ...
Page 20
... National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. ...