mc68hc711d3 Freescale Semiconductor, Inc, mc68hc711d3 Datasheet - Page 47

no-image

mc68hc711d3

Manufacturer Part Number
mc68hc711d3
Description
M Hc11 Microcontrollers Microcontroller
Manufacturer
Freescale Semiconductor, Inc
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
mc68hc711d3CFN2
Manufacturer:
DIODES
Quantity:
12 000
Part Number:
mc68hc711d3CFN2
Manufacturer:
MOT
Quantity:
5 510
Part Number:
mc68hc711d3CFN2
Manufacturer:
FREESCALE
Quantity:
3 431
Part Number:
mc68hc711d3CFN2
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
mc68hc711d3CFN3
Manufacturer:
FREESCALE
Quantity:
8 831
Part Number:
mc68hc711d3CFN3
Manufacturer:
FREESCALE
Quantity:
3 432
Part Number:
mc68hc711d3CFNE2
Manufacturer:
ALLEGEO
Quantity:
4 492
Part Number:
mc68hc711d3CFNE2
Manufacturer:
FREESCALE
Quantity:
1 489
Part Number:
mc68hc711d3CFNE2
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
mc68hc711d3CFNE3
Manufacturer:
SGS
Quantity:
6 218
Chapter 4
Resets, Interrupts, and Low-Power Modes
4.1 Introduction
This section describes the internal and external resets and interrupts of the MC68HC711D3 and its two
low power-consumption modes.
4.2 Resets
The microcontroller unit (MCU) can be reset in any of these four ways:
The RESET input consists mainly of a Schmitt trigger that senses the RESET line logic level.
4.2.1 RESET Pin
To request an external reset, the RESET pin must be held low for at least eight E-clock cycles, or for one
E-clock cycle if no distinction is needed between internal and external resets.
4.2.2 Power-On Reset (POR)
Power-on reset occurs when a positive transition is detected on V
turn on conditions and should not be used to detect any drop in the power supply voltage. If the external
RESET pin is low at the end of the power-on delay time, the processor remains in the reset condition until
RESET goes high.
4.2.3 Computer Operating Properly (COP) Reset
The MCU contains a watchdog timer that automatically times out unless it is serviced within a specific
time by a program reset sequence. If the COP watchdog timer is allowed to timeout, a reset is generated,
which drives the RESET pin low to reset the MCU and the external system.
In the MC68HC711D3, the COP reset function is enabled out of reset in normal modes. If the user does
not want the COP enabled, he must write a 1 to the NOCOP bit of the configuration control register
(CONFIG) after reset. This bit is writable only once after reset in normal modes (see
Control Register
register (OPTION) allow the user to select one of the four COP timeout rates.
relationship between CR1 and CR0 and the COP timeout period for various system clock frequencies.
Freescale Semiconductor
1. An active-low input to the RESET pin
2. A power-on reset (POR) function
3. A clock monitor failure
4. A computer operating properly (COP) watchdog timer timeout
for more information). Protected control bits (CR1 and CR0) in the configuration options
MC68HC711D3 Data Sheet, Rev. 2.1
DD
. This reset is used strictly for power
Table 4-1
2.3.3 Configuration
shows the
47

Related parts for mc68hc711d3