isp1520 NXP Semiconductors, isp1520 Datasheet - Page 47

no-image

isp1520

Manufacturer Part Number
isp1520
Description
Hi-speed Universal Serial Bus Hub Controller
Manufacturer
NXP Semiconductors
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
isp1520BD
Manufacturer:
PHILIPS
Quantity:
449
Part Number:
isp1520BD
Manufacturer:
ST-Ericsson Inc
Quantity:
10 000
Part Number:
isp1520BD
Manufacturer:
NXP
Quantity:
1 000
Part Number:
isp1520BD
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
isp1520BD
Manufacturer:
NXP
Quantity:
10 569
Part Number:
isp1520BDGA
Manufacturer:
ST-Ericsson Inc
Quantity:
10 000
Part Number:
isp1520BDGA
Manufacturer:
ST
0
Part Number:
isp1520BDUM
Manufacturer:
ST-Ericsson Inc
Quantity:
10 000
Company:
Part Number:
isp1520BDUM
Quantity:
20
Philips Semiconductors
ISP1520_4
Product data sheet
19.4 Manual soldering
19.5 Package related soldering information
During placement and before soldering, the package must be fixed with a droplet of
adhesive. The adhesive can be applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the adhesive is cured.
Typical dwell time of the leads in the wave ranges from 3 seconds to 4 seconds at 250 C
or 265 C, depending on solder material applied, SnPb or Pb-free respectively.
A mildly-activated flux will eliminate the need for removal of corrosive residues in most
applications.
Fix the component by first soldering two diagonally-opposite end leads. Use a low voltage
(24 V or less) soldering iron applied to the flat part of the lead. Contact time must be
limited to 10 seconds at up to 300 C.
When using a dedicated tool, all other leads can be soldered in one operation within
2 seconds to 5 seconds between 270 C and 320 C.
Table 47.
[1]
[2]
[3]
Package
BGA, HTSSON..T
SSOP..T
DHVQFN, HBCC, HBGA, HLQFP, HSO, HSOP,
HSQFP, HSSON, HTQFP, HTSSOP, HVQFN,
HVSON, SMS
PLCC
LQFP, QFP, TQFP
SSOP, TSSOP, VSO, VSSOP
CWQCCN..L
– smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the
The footprint must incorporate solder thieves at the downstream end.
For packages with leads on four sides, the footprint must be placed at a 45 angle to
the transport direction of the printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
For more detailed information on the BGA packages refer to the (LF)BGA Application Note (AN01026);
order a copy from your Philips Semiconductors sales office.
All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the
maximum temperature (with respect to time) and body size of the package, there is a risk that internal or
external package cracks may occur due to vaporization of the moisture in them (the so called popcorn
effect). For details, refer to the Drypack information in the Data Handbook IC26; Integrated Circuit
Packages; Section: Packing Methods .
These transparent plastic packages are extremely sensitive to reflow soldering conditions and must on no
account be processed through more than one soldering cycle or subjected to infrared reflow soldering with
peak temperature exceeding 217 C
body peak temperature must be kept as low as possible.
[5]
transport direction of the printed-circuit board.
, SO, SOJ
[3]
[1]
, TFBGA, VFBGA, XSON
Suitability of surface mount IC packages for wave and reflow soldering methods
[8]
, PMFP
[3]
, LBGA, LFBGA, SQFP,
[9]
, WQCCN..L
Rev. 04 — 28 April 2006
[8]
10 C measured in the atmosphere of the reflow oven. The package
Soldering method
Wave
not suitable
not suitable
suitable
not recommended
not recommended
not suitable
[4]
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Hi-Speed USB hub controller
[5][6]
[7]
ISP1520
Reflow
suitable
suitable
suitable
suitable
suitable
not suitable
[2]
47 of 53

Related parts for isp1520