at89c5131 ATMEL Corporation, at89c5131 Datasheet - Page 124

no-image

at89c5131

Manufacturer Part Number
at89c5131
Description
8-bit Flash Microcontroller With Full Speed Usb Device At89c5131
Manufacturer
ATMEL Corporation
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
at89c5131-S3SIL
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
at89c5131A-PUTUM
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
at89c5131A-RDTIL
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
at89c5131A-RDTUL
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
at89c5131A-RDTUM
Manufacturer:
ATMEL
Quantity:
5 000
Part Number:
at89c5131A-RDTUM
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
at89c5131A-S3SIM
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
at89c5131A-S3SUM
Manufacturer:
ATMEL
Quantity:
46
Part Number:
at89c5131A-UL
Manufacturer:
TI
Quantity:
12 500
Part Number:
at89c5131A-UL
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
at89c5131A-UM
Manufacturer:
TOSHIBA
Quantity:
1 200
Part Number:
at89c5131A-UM
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
at89c5131A-UM
Quantity:
300
Bulk/Interrupt OUT
Transactions in Ping-pong
Mode
122
AT89C5131
Figure 60. Bulk/Interrupt OUT Transactions in Ping-pong Mode
An endpoint will be first enabled and configured before being able to receive Bulk or
Interrupt packets.
When a valid OUT packet is received on the endpoint bank 0, the RXOUTB0 bit is set by
the USB controller. This triggers an interrupt if enabled. The firmware has to select the
corresponding endpoint, store the number of data bytes by reading the UBYCTLX and
UBYCTHX registers. If the received packet is a ZLP (Zero Length Packet), the
UBYCTLX and UBYCTHX register values are equal to 0 and no data has to be read.
When all the endpoint FIFO bytes have been read, the firmware will clear the RXOUB0
bit to allow the USB controller to accept the next OUT packet on the endpoint bank 0.
This action switches the endpoint bank 0 and 1. Until the RXOUTB0 bit has been
cleared by the firmware, the USB controller will answer a NAK handshake for each OUT
requests on the bank 0 endpoint FIFO.
When a new valid OUT packet is received on the endpoint bank 1, the RXOUTB1 bit is
set by the USB controller. This triggers an interrupt if enabled. The firmware empties the
bank 1 endpoint FIFO before clearing the RXOUTB1 bit. Until the RXOUTB1 bit has
been cleared by the firmware, the USB controller will answer a NAK handshake for each
OUT requests on the bank 1 endpoint FIFO.
The RXOUTB0 and RXOUTB1 bits are alternatively set by the USB controller at each
new valid packet receipt.
The firmware has to clear one of these two bits after having read all the data FIFO to
allow a new valid packet to be stored in the corresponding bank.
A NAK handshake is sent by the USB controller only if the banks 0 and 1 has not been
released by the firmware.
If the Host sends more bytes than supported by the endpoint FIFO, the overflow data
won’t be stored, but the USB controller will consider that the packet is valid if the CRC is
correct.
OUT
OUT
OUT
HOST
DATA0 (n Bytes)
DATA1 (m Bytes)
DATA0 (p Bytes)
ACK
ACK
ACK
UFI
RXOUTB0
RXOUTB1
RXOUTB0
Endpoint FIFO Bank 0 - Read Byte 1
Endpoint FIFO Bank 0 - Read Byte 2
Endpoint FIFO Bank 0 - Read Byte n
Endpoint FIFO Bank 1 - Read Byte 1
Endpoint FIFO Bank 1 - Read Byte 2
Endpoint FIFO Bank 1 - Read Byte m
Endpoint FIFO Bank 0 - Read Byte 1
Endpoint FIFO Bank 0 - Read Byte 2
Endpoint FIFO Bank 0 - Read Byte p
Clear RXOUTB0
Clear RXOUTB1
Clear RXOUTB0
C51
4136C–USB–04/05

Related parts for at89c5131