at89c5131 ATMEL Corporation, at89c5131 Datasheet - Page 93

no-image

at89c5131

Manufacturer Part Number
at89c5131
Description
8-bit Flash Microcontroller With Full Speed Usb Device At89c5131
Manufacturer
ATMEL Corporation
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
at89c5131-S3SIL
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
at89c5131A-PUTUM
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
at89c5131A-RDTIL
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
at89c5131A-RDTUL
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
at89c5131A-RDTUM
Manufacturer:
ATMEL
Quantity:
5 000
Part Number:
at89c5131A-RDTUM
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
at89c5131A-S3SIM
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
at89c5131A-S3SUM
Manufacturer:
ATMEL
Quantity:
46
Part Number:
at89c5131A-UL
Manufacturer:
TI
Quantity:
12 500
Part Number:
at89c5131A-UL
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
at89c5131A-UM
Manufacturer:
TOSHIBA
Quantity:
1 200
Part Number:
at89c5131A-UM
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
at89c5131A-UM
Quantity:
300
Master Mode
Slave Mode
Transmission Formats
92
AT89C5131
Figure 41. Full-duplex Master/Slave Interconnection
The SPI operates in Master mode when the Master bit, MSTR
is set. Only one Master SPI device can initiate transmissions. Software begins the trans-
mission from a Master SPI module by writing to the Serial Peripheral Data Register
(SPDAT). If the shift register is empty, the byte is immediately transferred to the shift
register. The byte begins shifting out on MOSI pin under the control of the serial clock,
SCK. Simultaneously, another byte shifts in from the Slave on the Master’s MISO pin.
The transmission ends when the Serial Peripheral transfer data flag, SPIF, in SPSTA
becomes set. At the same time that SPIF becomes set, the received byte from the Slave
is transferred to the receive data register in SPDAT. Software clears SPIF by reading
the Serial Peripheral Status register (SPSTA) with the SPIF bit set, and then reading the
SPDAT.
The SPI operates in Slave mode when the Master bit, MSTR
cleared. Before a data transmission occurs, the Slave Select pin, SS, of the Slave
device must be set to’0’. SS must remain low until the transmission is complete.
In a Slave SPI module, data enters the shift register under the control of the SCK from
the Master SPI module. After a byte enters the shift register, it is immediately transferred
to the receive data register in SPDAT, and the SPIF bit is set. To prevent an overflow
condition, Slave software must then read the SPDAT before another byte enters the
shift register
least one bus cycle before the Master SPI starts a transmission. If the write to the data
register is late, the SPI transmits the data already in the shift register from the previous
transmission.
Software can select any of four combinations of serial clock (SCK) phase and polarity
using two bits in the SPCON: the Clock POLarity (CPOL
(CPHA
effect on the transmission format. CPHA defines the edges on which the input data are
sampled and the edges on which the output data are shifted (Figure 42 and Figure 43).
The clock phase and polarity should be identical for the Master SPI device and the com-
municating Slave device.
1.
2.
3.
4.
4
The SPI module should be configured as a Master before it is enabled (SPEN set). Also
The SPI module should be configured as a Slave before it is enabled (SPEN set).
The maximum frequency of the SCK for an SPI configured as a Slave is the bus clock
Before writing to the CPOL and CPHA bits, the SPI should be disabled (SPEN =’0’).
). CPOL defines the default SCK line level in idle state. It has no significant
Clock Generator
the Master SPI should be configured before the Slave SPI.
speed.
(3)
SPI
. A Slave SPI must complete the write to the SPDAT (shift register) at
Master MCU
8-bit Shift Register
MOSI
SCK
SS
MISO
VDD
MISO
MOSI
SCK
VSS
SS
8-bit Shift Register
(2)
(4)
Slave MCU
(1)
, in the SPCON register is
) and the Clock PHAse
, in the SPCON register
4136C–USB–04/05

Related parts for at89c5131