iso1h815 Infineon Technologies Corporation, iso1h815 Datasheet

no-image

iso1h815

Manufacturer Part Number
iso1h815
Description
Coreless Transformer Isolated Digital Output 8 Channel 1.2a High-side Switch
Manufacturer
Infineon Technologies Corporation
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
iso1h815G
Manufacturer:
INFINEON
Quantity:
201
Part Number:
iso1h815G
0
Company:
Part Number:
iso1h815G
Quantity:
4 800
P r e l i m i n a r y D a t a s h e e t , V e r s i o n 1 . 0 , M a y 2 0 0 9
T M
I S O F A C E
I S O 1 H 8 1 5 G
C o r e l e s s T r a n s f o r m e r I s o l a t e d
D i g i t a l O u t p u t 8 C h a n n e l 1 . 2 A
H i g h - S i d e S w i t c h
P o w e r M a n a g e m e n t & D r i v e s
N e v e r
s t o p
t h i n k i n g .

Related parts for iso1h815

iso1h815 Summary of contents

Page 1

...

Page 2

... ISO1H815G Revision History: 2009-05-28 Previous Version: V0.1 V1.0 Preliminary Datasheet Edition 2009-05-28 Published by Infineon Technologies AG, Am Campeon 1-12, 85579 Neubiberg, Germany Infineon Technologies AG 2009. © All Rights Reserved. Attention please! The information herein is given to describe certain components and shall not be considered as a guarantee of characteristics. ...

Page 3

... DC applications • Driver for solenoid, relays and resistive loads Description The ISO1H815G is a galvanically isolated 8 bit data interface in PG-DSO-36 package that provides 8 fully protected high-side power switches that are able to handle currents up to 1.2A bit parallel µC compatible interface allows to connect the IC directly to a µ ...

Page 4

... DIAG 14 GNDCC 15 N.C. 16 N.C. 17 TAB N.C. 18 Vbb Figure 1 Power SO-36 (430mil ISOFACE ISO1H815G 36 OUT0 35 OUT0 34 OUT1 33 OUT1 32 OUT2 31 OUT2 30 OUT3 29 OUT3 28 OUT4 27 OUT4 26 OUT5 25 OUT5 24 OUT6 23 OUT6 22 OUT7 21 OUT7 20 N.C. 19 GNDbb Version 1.0, 2009-05-28 ...

Page 5

... DIS signal, till new information is written into the input register. Current Sink to GNDCC. CS (Chip select) The system microcontroller selects the ISO1H815G by means of the low active pin CS to activate the parallel interface. By connecting the CS pin and WR pin to ground the parallel direct control is activated. Current Source to VCC ...

Page 6

... Blockdiagram Figure 2 Blockdiagram Preliminary Datasheet Isolation Galvanic 6 TM ISOFACE ISO1H815G Blockdiagram Version 1.0, 2009-05-28 ...

Page 7

... Functional Description 3.1 Introduction The ISOFACE ISO1H815G includes 8 high-side power switches that are controlled by means of the integrated parallel interface. The interface is 8bit µC compatible. Furthermore a direct control mode can be selected that allows the direct control of the outputs OUT0...OUT7 by means of the inputs D0...D7 without any additional logic signal ...

Page 8

... The output stage at pin DIAG has an open drain functionality combined with a current source. DIAG t t Figure ISOFACE ISO1H815G Functional Description Normal Output short to GND operation I L(SCp) I L(SCr) Short circuit in on-state, shut down down by overtemperature, restart by ...

Page 9

... WR have to be connected both to ground. 3.5.1 Parallel Interface Signal Description CS - Chip select. The system microcontroller selects the ISO1H815G by means of the CS pin. Whenever the pin logic low state, data can be transferred from the µC. CS High to low transition: • Parallel input data can be written in from then on CS Low to high transition: • ...

Page 10

... This unit decides wether the transmitted data is valid or not. If four times serial data coming in from the internal registers is not accepted, the output stages are switched off until the next valid data is received. Preliminary Datasheet t WHCS t WRPW OUT0 - OUT7 10 TM ISOFACE ISO1H815G Functional Description t CSD t on/off Version 1.0, 2009-05-28 ...

Page 11

... GNDbb stg P tot 3) single Loaddump = 13. 27V A V ESD V ESD , each channel ISOFACE ISO1H815G Electrical Characteristics are internally galvanic isolated. bb Ω resistor in GNDbb connection. Limit Values min. max. -0.5 6 -0.5 6.5 -0.5 6.5 -0.5 6.5 -0.5 6.5 -0.5 6.5  self limited  -1.6 -25 internal limited °C -50 150  ...

Page 12

... Symbol min. ∆V 1) /dt -25 ISO H 100 IM 12 ISOFACE ISO1H815G Electrical Characteristics Limit Values Unit Test Condition typ. max.  1.5 K/W  50  38 Limit Values Unit Test Condition typ. max. mΩ 150 200 270 320 75 100 ...

Page 13

... I bb(uvlo)  I GNDL  I L(off) ) bb(off 2.5 CC(under)  V CC(u_rst)  ∆V CC(under)  I CC(uvlo)  I CC(on) 13 ISOFACE ISO1H815G Electrical Characteristics   10.5  11  0 < All Channels load 5 30 µA  5.5 V  2.9  3  ...

Page 14

... I L(SCr) each channel ON(CL bb(AZ) 2)3) T 135 jt  ∆T jt Symbol min. I diagsink = 135° diagsource 14 ISOFACE ISO1H815G Electrical Characteristics Limit Values Unit Test Condition typ. max. A  4.5  3.0    2.2 2.2 2     °C  Limit Values Unit Test Condition typ ...

Page 15

... WRPW    CSWR  WHCS  CSD 15 TM ISOFACE ISO1H815G Electrical Characteristics Unit Test Condition max. 0 0.3 mV µA 170 µs 230 Unit Test Condition max.  ns      ...

Page 16

... For Qualification Report please contact your local Infineon Technologies office! Preliminary Datasheet Symbol min    Value 500 ISO 1250 2.6 2.6 0.01 16 ISOFACE ISO1H815G Electrical Characteristics Limit Values Unit Test Condition typ. max. V  1  45  1.2 Unit Conditions minute duration acc ...

Page 17

... Preliminary Datasheet Electrical Characteristics 17 TM ISOFACE ISO1H815G Version 1.0, 2009-05-28 ...

Page 18

... Preliminary Datasheet Electrical Characteristics 18 TM ISOFACE ISO1H815G Version 1.0, 2009-05-28 ...

Page 19

... Does not include plastic or metal protrusion of 0.15 max. per side Figure 12 PG-DSO-36 Preliminary Datasheet 1.1 ±0.1 15.74 ±0.1 (Heatslug) 0.65 36x +0.13 0.25 0. 45˚ 1) 15.9 ±0.1 A (Mold) 19 ISOFACE ISO1H815G Package Outlines ±0. 2.8 6.3 0.1 C (Mold) 14.2 ±0.3 Bottom View 13.7 -0.2 (Metal) Version 1.0, 2009-05- Heatslug 0.95 ±0.15 0.25 B Heatslug gps09181_1 ...

Page 20

Total Quality Management Qualität hat für uns eine umfassende Bedeutung. Wir wollen allen Ihren Ansprüchen in der Weise gerecht werden. Es geht uns also nicht nur um die Produktqualität – unsere Anstrengungen gleichermaßen der Lieferqualität und Logistik, dem Service und ...

Related keywords