24lc02b-e-st Microchip Technology Inc., 24lc02b-e-st Datasheet
24lc02b-e-st
Related parts for 24lc02b-e-st
24lc02b-e-st Summary of contents
Page 1
... Note 1: 100 kHz for V <2.5V CC Features: • Single supply with operation down to 1.7V for 24AA02 devices, 2.5V for 24LC02B devices • Low-power CMOS technology: - Read current 1 mA, typical - Standby current 1 A, typical 2 • 2-wire serial interface, I C™ compatible • Schmitt Trigger inputs for noise suppression • ...
Page 2
... ELECTRICAL CHARACTERISTICS (†) Absolute Maximum Ratings V .............................................................................................................................................................................6.5V CC All inputs and outputs w.r.t. V ......................................................................................................... -0. Storage temperature ...............................................................................................................................-65°C to +150°C Ambient temperature with power applied ................................................................................................-40°C to +125°C ESD protection on all pins † NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device ...
Page 3
... This parameter is not tested but ensured by characterization. For endurance estimates in a specific application, please consult the Total Endurance™ Model which can be obtained from Microchip’s web site at www.microchip.com. © 2007 Microchip Technology Inc. 24AA02/24LC02B Industrial (I -40°C to +85° Automotive (E -40° ...
Page 4
... FIGURE 1-1: BUS TIMING DATA 5 3 SCL 7 6 SDA 14 IN SDA OUT FIGURE 1-2: BUS TIMING START/STOP SCL 6 7 SDA Start DS21709G-page Stop © 2007 Microchip Technology Inc. ...
Page 5
... SCL SDA Start Condition © 2007 Microchip Technology Inc. 24AA02/24LC02B 3.4 Data Valid (D) The state of the data line represents valid data when, after a Start condition, the data line is stable for the duration of the high period of the clock signal. The data on the line must be changed during the low period of the clock signal ...
Page 6
... Device Addressing A control byte is the first byte received following the Start condition from the master device. The control byte consists of a four-bit control code. For the 24XX02, this is set as ‘ 1010’ binary for read and write operations. The next three bits of the control byte are “don’t cares” ...
Page 7
... Block Select Bits x = don’t care © 2007 Microchip Technology Inc. 24AA02/24LC02B master has transmitted a Stop condition. Upon receipt of each word, the four lower-order Address Pointer bits are internally incremented by ‘ bits of the word address remain constant. If the master should transmit more than 8 words prior to generating the Stop condition, the address counter will roll over and the previously received data will be overwritten ...
Page 8
... ACKNOWLEDGE POLLING Since the device will not acknowledge during a write cycle, this can be used to determine when the cycle is complete (this feature can be used to maximize bus throughput). Once the Stop condition for a Write command has been issued from the master, the device initiates the internally-timed write cycle and ACK polling can then be initiated immediately ...
Page 9
... T SDA Line S Bus Activity x = “don’t care” © 2007 Microchip Technology Inc. 24AA02/24LC02B 7.3 Sequential Read Sequential reads are initiated in the same way as a random read, except that once the 24XX02 transmits the first data byte, the master issues an acknowledge as opposed to a Stop condition in a random read. This directs the 24XX02 to transmit the next sequentially- addressed 8-bit word (Figure 7-3) ...
Page 10
... FIGURE 7-2: RANDOM READ S T Bus Activity Control A Master Byte SDA Line Block Select Bus Activity x = “don’t care” FIGURE 7-3: SEQUENTIAL READ Bus Activity Control Master Byte Data (n) SDA Line Bus Activity K DS21709G-page ...
Page 11
... SCL low. Changes during SCL high are reserved for indicating Start and Stop conditions. 8.2 Serial Clock (SCL) The SCL input is used to synchronize the data transfer to and from the device. © 2007 Microchip Technology Inc. 24AA02/24LC02B DFN MSOP SOT23 — ...
Page 12
... TYWW NNN 8-Lead MSOP XXXXXT YWWNNN 5-Lead SOT-23 XXNN 8-Lead 2x3 DFN XXX YWW NN DS21709G-page 12 Example: 24LC02B e I/P 13F 3 0527 Example: 24LC02BI 0527 13F Example: 4L02 I527 13F Example: 4L2BI 52713F Example: M23F Example: 224 527 13 © 2007 Microchip Technology Inc. ...
Page 13
... Note: Please visit www.microchip.com/Pbfree for the latest information on Pb-free conversion. *Standard OTP marking consists of Microchip part number, year code, week code, and traceability code. © 2007 Microchip Technology Inc. 24AA02/24LC02B 1st Line Marking Codes SOT-23 MSOP I Temp. ...
Page 14
... Plastic Dual In-Line (P or PA) – 300 mil Body [PDIP] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging N NOTE Number of Pins Pitch Top to Seating Plane Molded Package Thickness Base to Seating Plane ...
Page 15
... Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.15 mm per side. 4. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. REF: Reference Dimension, usually without tolerance, for information purposes only. © 2007 Microchip Technology Inc. 24AA02/24LC02B ...
Page 16
... Plastic Thin Shrink Small Outline (ST) – 4.4 mm Body [TSSOP] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging D N NOTE Number of Pins Pitch Overall Height Molded Package Thickness Standoff Overall Width ...
Page 17
... Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.15 mm per side. 3. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. REF: Reference Dimension, usually without tolerance, for information purposes only. © 2007 Microchip Technology Inc. 24AA02/24LC02B ...
Page 18
... Plastic Small Outline Transistor (OT or CT) [SOT-23] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging Number of Pins Lead Pitch Outside Lead Pitch Overall Height Molded Package Thickness Standoff ...
Page 19
... Package may have one or more exposed tie bars at ends. 3. Package is saw singulated. 4. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. REF: Reference Dimension, usually without tolerance, for information purposes only. © 2007 Microchip Technology Inc. 24AA02/24LC02B EXPOSED PAD ...
Page 20
... APPENDIX A: REVISION HISTORY Revision C Corrections to Section 1.0, Electrical Characteristics. Revision D Added DFN package. Revision E Revised Figure 3-2 Control Byte Allocation; Figure 4-1 Byte Write; Figure 4-2 Page Write; Section 6.0 Write Protection; Figure 7-1 Current Address Read; Figure 7- 2 Random Read; Figure 7-3 Sequential Read. Revision F (01/2007) Revised Features section ...
Page 21
... To register, access the Microchip web site at www.microchip.com, click on Customer Change Notification and follow the registration instructions. © 2007 Microchip Technology Inc. 24AA02/24LC02B CUSTOMER SUPPORT Users of Microchip products can receive assistance through several channels: • Distributor or Representative • ...
Page 22
... Telephone: (_______) _________ - _________ Application (optional): Would you like a reply? Y Device: 24AA02/24LC02B Questions: 1. What are the best features of this document? 2. How does this document meet your hardware and software development needs you find the organization of this document easy to follow? If not, why? 4 ...
Page 23
... PART NO. X /XX Device Temperature Package Range Device: 24AA02: = 1.7V, 2 Kbit I 24AA02T: = 1.7V, 2 Kbit I (Tape and Reel) 24LC02B: = 2.5V, 2 Kbit I 24LC02BT: = 2.5V, 2 Kbit I (Tape and Reel) Temperature I = -40°C to +85°C Range -40°C to +125°C Package 2x3 DFN, 8-lead P = Plastic DIP (300 mil body), 8-lead ...
Page 24
... NOTES: DS21709G-page 24 2007 Microchip Technology Inc. ...
Page 25
... Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. © 2007 Microchip Technology Inc. Trademarks The Microchip name and logo, the Microchip logo, Accuron, dsPIC, K ...
Page 26
... Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 © 2007 Microchip Technology Inc. EUROPE Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 France - Paris ...