at27bv010 ATMEL Corporation, at27bv010 Datasheet
at27bv010
Available stocks
Related parts for at27bv010
at27bv010 Summary of contents
Page 1
... At V accessed in less than 90 ns. With a typical power draw of only MHz and V = 3V, the AT27BV010 consumes less than one fifth the power of a standard 5V CC EPROM. Standby mode supply current is typically less than 1 µA at 3V. The AT27BV010 simplifies system design and stretches battery lifetime even further by eliminating the need for power supply regulation ...
Page 2
... Programming time is typically only 100 µs/byte. The Integrated Product Identification Code electronically identifies the device and manufacturer. This feature is used by industry-standard programming equipment to select the proper programming algorithms and voltages. The AT27BV010 programs exactly the same way as a standard 5V AT27C010 and uses the same programming equipment. 2. Pin Configurations ...
Page 3
... Maximum Ratings” may cause permanent dam- age to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the (1) operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect (1) device reliability (1) AT27BV010 3 ...
Page 4
... ( ≤ 5.5V 6.5V except A9 which is set to V and A0 which is toggled select the Device Code byte. IH AT27BV010-90 -40°C - 85°C 2.7V to 3.6V 5V ± 10% Outputs D OUT High Z High OUT High Z Identification Code 0344H–EPROM–12/07 ...
Page 5
... 0.5V SB2 MHz mA OUT 2 -400 µ and removed simultaneously with or after except during programming. The supply current would then be the sum AT27BV010 Min Max Units ±1 µA ±5 µA 10 µA 20 µA 100 µ -0.6 0 ...
Page 6
... Timing measurement references are 0.8V and 2.0V. Input AC drive levels are 0.45V and 2.4V, unless otherwise specified may be delayed may be delayed This parameter is only sampled and is not 100% tested. 5. Output float is defined as the point when data is no longer driven. AT27BV010 6 Condition ...
Page 7
... Typ OUT Note: 1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested. 0344H–EPROM–12/ < (10 Note 100 pF including jig capacitance. Max 8 12 AT27BV010 Units Conditions OUT 7 ...
Page 8
... Programming Waveforms Notes: 1. The Input Timing Reference is 0.8V for and t are characteristics of the device but must be accommodated by the programmer. OE DFP 3. When programming the AT27BV010, a 0.1 µF capacitor is required across V transients. AT27BV010 8 (1) and 2.0V for and ground to suppress spurious voltage PP 0344H–EPROM–12/07 ...
Page 9
... Program Pulse width tolerance is 100 17. Atmel’s AT27BV010 Integrated Product Identification Code Codes A0 Manufacturer 0 Device Type 1 Note: 1. The AT27BV010 has the same Product Identification Code as the AT27C010. Both are programming compatible. 0344H–EPROM–12/07 = 13.0 ± 0.25V PP Test Conditions ...
Page 10
... After the byte verifies properly, the next address is selected until all have been checked. V read again and compared with the original data to determine if the device passes or fails. AT27BV010 10 is raised to 13.0V. Each address is first programmed with one 100 µ then lowered to 5 ...
Page 11
... Plastic Thin Small Outline Package (TSOP) 32V 33-lead, Plastic Thin Small Outline Package (VSOP) 0344H–EPROM–12/07 Ordering Code AT27BV010-90JI AT27BV010-90TI AT27BV010-90VI Ordering Code AT27BV010-90JU AT27BV010-90TU Package Type AT27BV010 Package Operation Range 32J Industrial 32T (-40°C to 85°C) (1) 32V ...
Page 12
... Allowable protrusion is .010"(0.254 mm) per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line. 3. Lead coplanarity is 0.004" (0.102 mm) maximum. 2325 Orchard Parkway San Jose, CA 95131 R AT27BV010 12 1.14(0.045) X 45˚ PIN NO. 1 IDENTIFIER E1 E ...
Page 13
... Orchard Parkway San Jose, CA 95131 R 0344H–EPROM–12/07 PIN SEATING PLANE A1 TITLE 32T, 32-lead ( Package) Plastic Thin Small Outline Package, Type I (TSOP) AT27BV010 0º ~ 8º GAGE PLANE COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX A – ...
Page 14
... This package conforms to JEDEC reference MO-142, Variation BA. 2. Dimensions D1 and E do not include mold protrusion. Allowable protrusion 0.15 mm per side and 0.25 mm per side. 3. Lead coplanarity is 0.10 mm maximum. 2325 Orchard Parkway San Jose, CA 95131 R AT27BV010 14 PIN SEATING PLANE ...
Page 15
... Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © 2007 Atmel Corporation. All rights reserved. Atmel Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. International Atmel Asia ...