tza3011a NXP Semiconductors, tza3011a Datasheet
tza3011a
Related parts for tza3011a
tza3011a Summary of contents
Page 1
... The design is made in the Philips BiCMOS RF process and is available in a HBCC32 package or as bare die. The TZA3011A is intended for use in an application with an AC-coupled laser diode with a 3.3 V laser supply voltage. The TZA3011B is intended for use in an application with a DC-coupled laser diode for both 3.3 V and 5 V laser supply voltages ...
Page 2
... Mbit 3.2 Gbit/s A-rate Ordering information Name Description HBCC32 plastic thermal enhanced bottom chip carrier; 32 terminals; body 5 - bare die; 2 560 Rev. 06 — 20 January 2005 TZA3011A; TZA3011B 5 0. 510 380 m © Koninklijke Philips Electronics N.V. 2005. All rights reserved. laser drivers Version SOT560-1 - ...
Page 3
... CIN CINQ V 1.32 V CCD I /750 BIAS R ALARM I /1500 mod OPERATING CURRENT Q enable (17) 11 (18) GNDDFT ALOP Rev. 06 — 20 January 2005 TZA3011A; TZA3011B 30 Mbit 3.2 Gbit/s A-rate ACDC BIASOUT BIASIN MON 29 (52) 28 (50) 27 (49) 26 (48) I 100 A 100 A BIAS V/I 100 mA/V V/I 100 mA/V 100 100 PRE ...
Page 4
... Philips Semiconductors 6. Pinning information 6.1 Pinning Fig 2. Pin configuration TZA3011A and TZA3011B 9397 750 14437 Product data sheet TZA3011A; TZA3011B 30 Mbit 3.2 Gbit/s A-rate V 1 CCA V 2 CCD DIN 3 DINQ 4 TZA3011AVH TEST 5 TZA3011BVH CIN 6 CINQ 7 GND 8 ALRESET 9 Transparent top view Rev. 06 — 20 January 2005 ...
Page 5
... CIN 12 CINQ 13 TZA3011UH Pin description TZA3011A and TZA3011B Pin Description die pad common ground plane for V connected to ground 1 analog supply voltage 2 digital supply voltage 3 non-inverted data input (RF input) 4 inverted data input (RF input) 5 test pin or test pad; must be connected to ground ...
Page 6
... TEST CIN CINQ GNDESD ALRESET 9397 750 14437 Product data sheet 30 Mbit 3.2 Gbit/s A-rate Pin description TZA3011A and TZA3011B Pin Description 13 threshold level input for alarm on operating current 14 temperature dependent voltage output source 15 threshold level input for alarm on monitor diode current 16 reference current input ...
Page 7
... Rev. 06 — 20 January 2005 TZA3011A; TZA3011B [1] …continued Description enable input for modulation and bias current ground alarm output on operating current (open-drain) alarm output on monitor diode current (open-drain) internally connected threshold level input for alarm on operating current ...
Page 8
... GND potential through substrate contacts < 440 C; recommended die attachment is by gluing < Rev. 06 — 20 January 2005 TZA3011A; TZA3011B [1] …continued Description ground input for the monitor photodiode (RF input) input for the bias current setting output of the control block for the bias current ...
Page 9
... The LA output is optimized for the laser allowing dynamic range and a 1.2 V minimum voltage. The LAQ output is optimized for the dummy load. The output stage of the TZA3011A is optimized for AC-coupled lasers and the output stage of the TZA3011B is optimized for DC-coupled lasers. ...
Page 10
... The alarm threshold levels are programmed by a resistor or a current source. In the TZA3011A, for the AC-coupled application, the operating current is equal to the bias current. In the TZA3011B, for the DC-coupled application, the operating current equals the bias current plus half of the modulation current ...
Page 11
... MAXOP, MAXMON, RREF, PWA, ER and AVR VTEMP, BIASOUT and MODOUT ALOP, ALMON and MON ambient temperature junction temperature storage temperature Rev. 06 — 20 January 2005 TZA3011A; TZA3011B Min 0.5 0.5 0.5 0.5 1.2 = 3.3 V CCO 0.8 = 3.3 V CCO 1.2 ...
Page 12
... CCD i(CIN) CCD AC-coupled inputs CIN CINQ 2500 A MON 2500 A MON Rev. 06 — 20 January 2005 TZA3011A; TZA3011B 30 Mbit 3.2 Gbit/s A-rate = 3. 3. CCD = PWA RREF Min Typ 3.14 3.3 3.14 3.3 3.14 3.3 4.75 5 ...
Page 13
... Bias current source: pins BIASIN and BIAS g bias transconductance m(bias) I source current at source(BIASIN) pin BIASIN 9397 750 14437 Product data sheet TZA3011A; TZA3011B 30 Mbit 3.2 Gbit/s A-rate = 400 tot CCA = 6 6 MODIN BIASIN Conditions dual-loop set-up; IER > ...
Page 14
... CCO 3 CCO V = 0.5 V MODIN V = 1.5 V MODIN V < 0.8 V ENABLE TZA3011A 3.3 V CCO TZA3011B 3.3 V CCO TZA3011B CCO bias and modulation currents disabled bias and modulation currents enabled no reset reset Rev. 06 — 20 January 2005 = 3. 3. CCD = ...
Page 15
... A. Therefore, for large ER settings, minimum/maximum AVR MON MON and the modulation current I o(LA amb tot th(j-a) Rev. 06 — 20 January 2005 TZA3011A; TZA3011B 30 Mbit 3.2 Gbit/s A-rate = 3. 3. CCD = PWA RREF Min Typ 1.15 1.2 700 800 750 ...
Page 16
... PWA PWA PWA PWA = 14 mA when mA. o(LA) mod are impacted by total inductance between the LA pins and the laser connection. f Rev. 06 — 20 January 2005 TZA3011A; TZA3011B 30 Mbit 3.2 Gbit/s A-rate = 3. 3. CCD = PWA RREF Min Typ 0.03 - 0.03 ...
Page 17
... Figure 5. respectively, this allows resistor tuning to start at a minimum current level. I mod 1.5 V (V) BIASIN mgt890 Fig 5. Modulation current as a function of MODIN Rev. 06 — 20 January 2005 TZA3011A; TZA3011B 30 Mbit 3.2 Gbit/s A-rate and R BIASIN MODIN [mA [mA] 105 = I o(LA) (mA m(mod) 100 mA/V ...
Page 18
... AVR – ----------- - 2 A Figure 6. to start at minimum I AVR I av(MON 1500 Rev. 06 — 20 January 2005 TZA3011A; TZA3011B ) connected to ground: AVR AVR ------------ - R AVR – --------- - ----------- - increasing R AVR current level. AVR I = 1580 5.26 I ...
Page 19
... MAXOP R MAXOP = I BIAS I mod = I + ---------- - BIAS 2 Rev. 06 — 20 January 2005 TZA3011A; TZA3011B 30 Mbit 3.2 Gbit/s A-rate ) corresponding with an optical MON is from 200 A MAXOP MAXOP to ground: MAXOP © Koninklijke Philips Electronics N.V. 2005. All rights reserved. laser drivers MON(one) and MON(one) current can be ...
Page 20
... R PWA range is from 100 ps to +100 ps which corresponds with a R 100 t PWA (ps) 6.7 0 100 Rev. 06 — 20 January 2005 TZA3011A; TZA3011B 30 Mbit 3.2 Gbit/s A-rate is from 200 A MAXMON MAXMON to ground: MAXMON PWA PWA (k ) mgt893 © Koninklijke Philips Electronics N.V. 2005. All rights reserved. ...
Page 21
... Philips Semiconductors 12.2 TZA3011A with dual-loop control A simplified application using the TZA3011A with dual-loop control and with an AC-coupled laser at 3.3 V laser voltage is illustrated in and the extinction ratio are determined by the resistors R BIASOUT outputs are connected to the MODIN and the BIASIN inputs respectively. The ...
Page 22
... V CCD 2 DIN 3 DINQ 4 TEST 5 TZA3011B CIN 6 CINQ 7 GND 8 ALRESET Rev. 06 — 20 January 2005 TZA3011A; TZA3011B Figure 9. The average power level and and R . The MODOUT and AVR ER laser with monitor diode BIAS 24 GND LAQ 20 LAQ 19 GND ...
Page 23
... CCD 2 DIN 3 DINQ 4 TEST 5 TZA3011B CIN 6 CINQ 7 GND 8 ALRESET Rev. 06 — 20 January 2005 TZA3011A; TZA3011B Figure 10. The ER pin is short-circuited and the 100 A source current of the MODIN laser with monitor diode BIAS 24 GND LAQ 20 LAQ 19 GND ...
Page 24
... 2.5 scale 0.5 0.50 0.50 5.1 3.2 5.1 3.2 0.3 0.35 0.35 4.9 3.0 4.9 3.0 REFERENCES JEDEC JEITA MO-217 Rev. 06 — 20 January 2005 TZA3011A; TZA3011B 30 Mbit 3.2 Gbit/s A-rate detail ...
Page 25
... For packages with leads on two sides and a pitch (e): – larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be parallel to the transport direction of the printed-circuit board; 9397 750 14437 Product data sheet TZA3011A; TZA3011B 30 Mbit 3.2 Gbit/s A-rate 2 called small/thin packages. ...
Page 26
... LBGA, LFBGA, SQFP, [3] , TFBGA, VFBGA, XSON , SO, SOJ [8] [9] [8] , PMFP , WQCCN.. measured in the atmosphere of the reflow oven. The package Rev. 06 — 20 January 2005 TZA3011A; TZA3011B 30 Mbit 3.2 Gbit/s A-rate Soldering method Wave not suitable [4] not suitable suitable [5] [6] not recommended [7] not recommended not suitable © ...
Page 27
... The appropriate soldering profile can be provided on request. [9] Hot bar soldering or manual soldering is suitable for PMFP packages. 9397 750 14437 Product data sheet TZA3011A; TZA3011B 30 Mbit 3.2 Gbit/s A-rate Rev. 06 — 20 January 2005 laser drivers © Koninklijke Philips Electronics N.V. 2005. All rights reserved. ...
Page 28
... Philips Semiconductors 15. Revision history Table 10: Revision history Document ID Release date TZA3011A_TZA3011B_6 20050120 Product data sheet • Modifications: The format of this data sheet has been redesigned to comply with the new presentation and information standard of Philips Semiconductors. • change unit bits/s to bit/s. ...
Page 29
... It is the responsibility of the customer to test and qualify their application in which the die is used. 19. Trademarks A-Rate — trademark of Koninklijke Philips Electronics N.V. Rev. 06 — 20 January 2005 TZA3011A; TZA3011B © Koninklijke Philips Electronics N.V. 2005. All rights reserved. laser drivers ...
Page 30
... Bias and modulation currents . . . . . . . . . . . . . 17 12.1.2 Average monitor current and extinction ratio . 18 12.1.3 Dual-loop control 12.1.4 Alarm operating current . . . . . . . . . . . . . . . . . 19 12.1.5 Alarm monitor current . . . . . . . . . . . . . . . . . . . 20 12.1.6 Pulse width adjustment 12.2 TZA3011A with dual-loop control . . . . . . . . . . 21 12.3 TZA3011B with dual-loop control . . . . . . . . . . 22 12.4 TZA3011B with average loop control . . . . . . . 23 13 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 24 14 Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 14.1 Introduction to soldering surface mount packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 14.2 Refl ...