s-882152amh-m3btfg Seiko Instruments Inc., s-882152amh-m3btfg Datasheet
s-882152amh-m3btfg
Related parts for s-882152amh-m3btfg
s-882152amh-m3btfg Summary of contents
Page 1
... Power supply for white LED display backlights Packages Package Name SOT-23-6W The S-8821 series is a CMOS step-up charge pump DC-DC converter with a voltage regulation function. The S-8821 series consists of an oscillation circuit, a controller, a reference voltage circuit, an error amplifier circuit, and an output switching transistor, and can regulate the output voltage by PFM control ...
Page 2
... VOLTAGE REGULATION STEP-UP CHARGE PUMP DC-DC CONVERTER S-8821 Series Block Diagram VIN =4.7 μ SW1 SW2 C + =0.10 μ PUMP C − SW3 SW4 2 PFM control Switch oscillator control circuit circuit (1.0 MHz) Soft start circuit ON/OFF circuit ON/OFF Figure 1 Seiko Instruments Inc. Rev.3.1 _00 VOUT =10 μ ...
Page 3
... S-882130AMH-M2FTFG 3.3 V S-882133AMH-M2ITFG 3.5 V S-882135AMH-M2KTFG 3.6 V S-882136AMH-M2LTFG 4.0 V S-882140AMH-M2PTFG 4.5 V S-882145AMH-M2UTFG 5.0 V S-882150AMH-M2ZTFG 5.2 V S-882152AMH-M3BTFG 5.5 V S-882155AMH-M3ETFG Remark Contact the SII sales department for products with an output voltage other than those specified above. – xxx direction in tape specifications Product name (abbreviation) Package name (abbreviation) MH: SOT-23-6W Output voltage ...
Page 4
... C+ (positive pin) Charge-pump pump capacitor connection pin 3 C− (negative pin) Shutdown pin 4 ON/OFF High level (H) : normal operation (step-up) Low level (L) : step-up halt (all circuit halt) 5 GND GND pin 6 VOUT Voltage output pin Seiko Instruments Inc. Rev.3.1 Table 2 Pin Description ...
Page 5
... Board size: (2) Board name: JEDEC STANDARD51-7 Caution The absolute maximum ratings are rated values exceeding which the product could suffer physical damage. These values must therefore not be exceeded under any conditions. (1) When mounted on board 800 ...
Page 6
... In case of V =2.0 V OUT IN * Actual output voltage OUT( Specified output voltage OUT(S) *3. The output current at which the output voltage becomes output current. *4. Design assurance *5. The ideal efficiency is indicated by the following expression. × I Efficiency (η)=(V OUT OUT ≤ 2 *6. In case ...
Page 7
... VOLTAGE REGULATION STEP-UP CHARGE PUMP DC-DC CONVERTER Rev.3.1 _00 Test Circuits 1. 4.7 μ 0.1 μF 4.7 μF A VIN VOUT C+ GND C− ON/OFF A Figure 4 VIN VOUT C+ GND C− ON/OFF 10 μF A Figure 5 Seiko Instruments Inc. S-8821 Series A 7 ...
Page 8
... Figure 6 shows the block diagram of the S-8821 Series. The S-8821 series controls the output voltage by using the pulse frequency modulation (PFM) method. The SW1 to SW4 switching transistors are switched ON/OFF with the clock generated by the internal oscillator circuit, and operates the step-up charge pump. ...
Page 9
... SW4 to ON (charge cycle). Following charging the electricity, in order to discharge the charged electricity to the output capacitance (C and SW4 to OFF (discharge cycle). The input voltage can be stepped constant voltage value by repeating this charge cycle and discharge cycle. Figure 7 shows the charge cycle, and Figure 8 shows the discharge cycle. ...
Page 10
... S-8821 Series 3. Shutdown Pin (ON/OFF Pin) Setting the ON/OFF pin to the Low level ("L") causes the voltage of the VOUT pin to change to the GND level and simultaneously the operation of all the internal circuit to stop. At this time, the consumption current is largely reduced level of approximately 0.3 μA. ...
Page 11
... Select a ceramic IN capacitor with a small equivalent series resistance (ESR). Although this figure varies according to the impedance of the power supply that is used as well as the load current value generally in the range of 4.7 μ μF. For the output capacitor (C voltage. A value of 10 μ ...
Page 12
... Moreover, in selecting C PUMP • The ON/OFF pin is configured as shown in Figure 9 and is neither pulled up or down internally not use this pin in a floating state. When not using the ON/OFF pin, connect it to the VIN pin. Moreover, please do not apply voltage higher than VIN + 0 ON/OFF pin. Current flows for a VIN pin through the protection diode inside IC. • ...
Page 13
... VOLTAGE REGULATION STEP-UP CHARGE PUMP DC-DC CONVERTER Rev.3.1 _00 Characteristics (Typical Data) (1) Output voltage vs. Operation input voltage S-882133A I OUT 3.50 3.45 3.40 3.35 3.30 3.25 3.20 3.15 3.10 1.5 2.0 2.5 3.0 3.5 4.0 V [V] IN (2) Output voltage vs. Output current S-882133A V 3.50 3.45 3.40 3.35 3.30 3.25 3.20 3.15 3. [mA] OUT (3) Operation consumption vs. Operation input voltage S-882133A 1.5 2.0 2.5 3.0 3.5 4.0 V [V] IN S-882150A =10 mA, Ta=25° ...
Page 14
... V [ (5) Efficiency vs. Operation input voltage S-882133A I OUT 100 1.5 2.0 2.5 3.0 3.5 V [V] IN *1. The ideal efficiency is indicated by the following expression. × I Efficiency (η)=(V OUT (6) Maximum oscillation frequency vs. Operation input voltage S-882133A 1300 1200 1100 1000 900 800 700 1.5 2.0 2.5 3.0 3 S-882150A =10 mA, Ta=25° ...
Page 15
... VOLTAGE REGULATION STEP-UP CHARGE PUMP DC-DC CONVERTER Rev.3.1 _00 (7) Load fluctuation S-882133A CH1 10 mA CH2 ms/div.] CH1: V CH2: I (8) Input voltage fluctuation S-882133A CH1 3.3 V CH2 1 ms/div.] CH1: V CH2: V S-882150A V =2 CH1 CH2 [20 mV/div.] OUT [2 mA/div.] OUT S-882150A I =10 mA OUT CH1 CH2 [20 mV/div ...
Page 16
...
Page 17
...
Page 18
...
Page 19
... Use of the information described herein for other purposes and/or reproduction or copying without the express permission of Seiko Instruments Inc. is strictly prohibited. The products described herein cannot be used as part of any device or equipment affecting the human body, such as exercise equipment, medical equipment, security systems, gas equipment, or any apparatus installed in airplanes and other vehicles, without prior written permission of Seiko Instruments Inc ...