mic4452 Micrel Semiconductor, mic4452 Datasheet - Page 7

no-image

mic4452

Manufacturer Part Number
mic4452
Description
12a-peak Low-side Mosfet Driver Bipolar/cmos/dmos Process
Manufacturer
Micrel Semiconductor
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
mic4452VM
Manufacturer:
PULSE
Quantity:
3 100
Part Number:
mic4452YM
Manufacturer:
MICREL/麦瑞
Quantity:
20 000
Part Number:
mic4452YM
0
Part Number:
mic4452YN
Manufacturer:
AvagoTechnologiesUSInc
Quantity:
2 000
Part Number:
mic4452YN
Manufacturer:
MICROCHI
Quantity:
20 000
Part Number:
mic4452ZT
Manufacturer:
FSC
Quantity:
7 000
MIC4451/4452
Applications Information
Supply Bypassing
Charging and discharging large capacitive loads quickly
requires large currents. For example, changing a 10,000pF
load to 18V in 50ns requires 3.6A.
The MIC4451/4452 has double bonding on the supply pins,
the ground pins and output pins. This reduces parasitic lead
inductance. Low inductance enables large currents to be
switched rapidly. It also reduces internal ringing that can
cause voltage breakdown when the driver is operated at or
near the maximum rated voltage.
Internal ringing can also cause output oscillation due to
feedback. This feedback is added to the input signal since it
is referenced to the same ground.
CONTROL 1 8 0 ° TO 3 6 0 °
July 2005
CONTROL 0° TO 180°
CONDUCTION ANGLE
CONDUCTION ANGLE
φ 1 D R I V E S I G N A L
0.1µF
50V
0.1µF
WIMA
MKS2
2
+15
MIC4451
1
4
Figure 3. Direct Motor Drive
8
5
D R I V E
LOGIC
+
(x2) 1N4448
6, 7
UNIT E D CHE MCON S X E
1µF
50V
MKS2
MIC4451
MIC4452
5.6 kΩ
560 Ω
V DD
V DD
560µF 50V
PHASE 1 OF 3 PHASE MOTOR
D R I VER U SI N G M I C 4 4 5 1 / 4 4 5 2
1 µ F
1 µ F
φ
Figure 4. Self Contained Voltage Doubler
+
1
100µF 50V
M
BYV 10 (x 2)
φ
2
V DD
V DD
+
φ
3
7
To guarantee low supply impedance over a wide frequency
range, a parallel capacitor combination is recommended for
supply bypassing. Low inductance ceramic disk capacitors
with short lead lengths (< 0.5 inch) should be used. A 1µF
low ESR film capacitor in parallel with two 0.1µF low ESR
ceramic capacitors, (such as AVX RAM GUARD
adequate bypassing. Connect one ceramic capacitor directly
between pins 1 and 4. Connect the second ceramic capacitor
directly between pins 8 and 5.
Grounding
The high current capability of the MIC4451/4452 demands
careful PC board layout for best performance. Since the
MIC4451 is an inverting driver, any ground lead impedance
will appear as negative feedback which can degrade switch-
ing speed. Feedback is especially noticeable with slow-rise
time inputs. The MIC4451 input structure includes 200mV
of hysteresis to ensure clean transitions and freedom from
oscillation, but attention to layout is still recommended.
Figure 5 shows the feedback effect in detail. As the MIC4451
input begins to go positive, the output goes negative and
several amperes of current flow in the ground lead. As little
as 0.05Ω of PC trace resistance can produce hundreds of
millivolts at the MIC4451 ground pins. If the driving logic is
referenced to power ground, the effective logic input level is
reduced and oscillation may result.
To insure optimum performance, separate ground traces
should be provided for the logic and power connections. Con-
necting the logic ground directly to the MIC4451 GND pins
will ensure full logic drive to the input and ensure fast output
switching. Both of the MIC4451 GND pins should, however,
still be connected to power ground.
30
29
28
27
26
25
0
OUTPUT VOLTAGE vs LOAD CURREN T
50 100 150 200 250 300 350
mA
12 Ω LIN E
MIC4451/4452
®
Micrel, Inc.
), provides

Related parts for mic4452