sc473mltrt Semtech Corporation, sc473mltrt Datasheet

no-image

sc473mltrt

Manufacturer Part Number
sc473mltrt
Description
Sc473 Single-phase Single Chip Graphics Core Power Supply
Manufacturer
Semtech Corporation
Datasheet
The SC473 is a single-phase chip, high-performance PWM
controller designed to power advanced graphic cores. On-
chip support is provided that includes slew-rate controlled
VID transitions.
The SC473 implements hysteretic control technology which
provides the fastest possible transient response while
avoiding the stability issues inherent to classical PWM
controllers. Eliminating the sense resistors reduces costs
and PCB area, plus increases system effi ciency. Integrated
SmartDriver™ technology initially turns on the high-side
driver with ‘soft’ drive to reduce ringing, EMI, and capaci-
tive turn-on of the low side MOSFET, while also increasing
overall effi ciency.
Hysteretic operation adaptively reduces the SC473 switch-
ing frequency at light loads. Combined with an automatic
“powersave” mode which prevents negative current fl ow in
the low-side FET, system effi ciency is signifi cantly enhanced
during light loading conditions.
A 5-bit DAC, accurate to 0.85%, sets the output voltage
reference, and implements the voltage range required by
the processor. The DAC slew rate is externally programmed
to minimize transient currents and audible noise. True
differential remote sensing provides accurate point-of-load
regulation at the processor die. Other features include
programmable soft-start, an open-drain PWRGD output,
dual-level over-voltage and programmable over-current pro-
tection. The SC473 is available in a space-saving 4x4mm,
24-pin MLP package.
Updated - Aug 17, 2006
POWER MANAGEMENT
Description
1
Features
Applications
Single-Phase Solution with Integrated Drivers
Hysteretic Control for Fast Transient Response
SmartDriver™ for reduced EMI
True Differential Remote (die) Sensing
VID Programmed Voltage
Delayed Power Good Signal with Blanking
Programmable Soft-Start and DAC Slew Control
Programmable OCP Threshold
Supports all Ceramic Decoupling Solutions
24-Pin MLP (4x4)
Lead-Free Package
RoHS and WEEE compliant
High Performance Graphics
Embedded Applications
Graphics Core Power Supply
Single-Phase Single Chip
www.semtech.com
SC473

Related parts for sc473mltrt

sc473mltrt Summary of contents

Page 1

POWER MANAGEMENT Description The SC473 is a single-phase chip, high-performance PWM controller designed to power advanced graphic cores. On- chip support is provided that includes slew-rate controlled VID transitions. The SC473 implements hysteretic control technology which provides the fastest possible ...

Page 2

POWER MANAGEMENT Typical Application Circuit SC473 © 2006 Semtech Corp ...

Page 3

POWER MANAGEMENT Absolute Maximum Ratings Exceeding the specifi cations below may result in permanent damage to the device or device malfunction. Operation outside of the parameters specifi the Electrical Characteristics section is not implied. Parameter Supply Voltage (V5) ...

Page 4

POWER MANAGEMENT Electrical Characteristics (Cont.) Parameter Logic Inputs (EN, VID [4:0]) Enable Threshold VID [4:0] Threshold Input Impedance Reference (DAC, SS, VREF), (0 < T DAC Error + Internal Offset DAC Sink/Source Ability SS Slew Current SS Discharge Threshold VREF ...

Page 5

POWER MANAGEMENT Electrical Characteristics (Cont.) Parameter Current Sensing (CS+, CS-) (Cont.) Low-Pass Filter Corner Frequency (1) Current Limit Combined System (CLSET) CL System Accuracy CLSET Input Bias Current Hysteresis Setting (HYS) HYS Input Bias Current HYS Gain (internal hysteresis setting ...

Page 6

POWER MANAGEMENT Electrical Characteristics (Cont.) Parameter High-Side Driver (TG, BST, DRN) Peak Current (1)(2) On-Resistance Rise Time (1, 2) Fall Time (1, 2) Propagation Delay (1, 2) Shoot-thru Protection Delay (1) Lower-Side Driver (BG, V5, PGND) Peak Current (1, 2) ...

Page 7

... SC473 Pin Out Diagram Top View Marking Information yyww = Date Code (Example: 0550) xxxxx = Semtech Lot Number (Example: E9000) xxxxx = (Example: 1–100) © 2006 Semtech Corp. Ordering Information Device SC473MLTRT 18 PWRGD SC473EVB RAMP Notes: 15 CS+ 1) Only available in tape and reel packaging. A reel contains 3000 ...

Page 8

POWER MANAGEMENT Pin Descriptions SC473 Pin Confi guration Pin # Pin Name 1 VID4 VID most signifi cant bit 2 VID3 3 VID2 4 VID1 5 VID0 VID least signifi cant bit Core comparator hysteresis - a resistor divider from ...

Page 9

POWER MANAGEMENT Block Diagram VID DAC [4:0] SS FB- - FB+ CS+ + CS- - CURRENT SENSE AMP CL_hi CLSET CL_lo HYS_hi HYS HYS_lo EN EN © 2006 Semtech Corp ERROR AMP - HYSTERETIC COMPARATOR + + - ...

Page 10

POWER MANAGEMENT Applications Information Introduction The SC473 is a new generation of hysteretic converters which combines the best features of Semtech’s hysteretic converter technology with the benefi error amplifi er. The SC473 provides a complete solution to ...

Page 11

POWER MANAGEMENT Applications Information (Cont.) Start-Up and Soft-Off Sequences: For the SC473 cold start-up, V5 must rise above its under- voltage lockout (UVLO) threshold (4.4V typ.) The EN signal may go high either before UVLO or after (preferred). The DAC ...

Page 12

POWER MANAGEMENT Applications Information (Cont.) DC Sense Voltage RCS LOAD RCS LOAD L1 L-R Rcs R25 R25 100 100 Power Monitor Implementation for SC473 (R Sense) IR33 VDCR (R25 R25 VR33 IR33 R33 PMON_Ideal V ...

Page 13

POWER MANAGEMENT Applications Information (Cont.) Component High Side MOSFET, HSFET Low Side MOSFET, LSFET Boost Capacitor, Cbst Boost Diode, Dbst Output Inductor, L Decoupling Capacitors Current Sense Resistor Output Bulk Capacitors Company Contact Web: http://www.irf.com/product-info/ International Rectifi er Phone: (310) ...

Page 14

POWER MANAGEMENT Applications Information (Cont.) EN VID4 ...

Page 15

POWER MANAGEMENT Typical Characteristics Nominal Load Regulation vs. Output Current V = 1.1500V Min-Max limits @ +/- 1% OUT 1.1800 1.1700 1.1600 1.1500 1.1400 1.1300 1.1200 0.00 2.00 4.00 6.00 8.00 10.00 12.00 14.00 16.00 18.00 20.00 22.00 24.00 26.00 ...

Page 16

POWER MANAGEMENT Typical Characteristics Figure 7 – Nominal Operation @ Iout = 30A Figure 9 – Output Voltage with 24A load step *Above performance graphs correspond to Applications Schematic on page 2 © 2006 Semtech Corp. Figure 8 – Voltage ...

Page 17

POWER MANAGEMENT Outline Drawing - MLP-32 Outline Drawing - MLP 4x4-24 © 2006 Semtech Corp. 17 SC473 www.semtech.com ...

Page 18

... POWER MANAGEMENT Land Pattern - MLP-32 Land Pattern - MLP 4x4-24 Contact Information Phone: (805) 498-2111 Fax: (805) 498-3804 © 2006 Semtech Corp. Semtech Corporation Power Management Products Division 200 Flynn Road, Camarillo, CA 93012 18 SC473 www.semtech.com ...

Related keywords