tza1049 NXP Semiconductors, tza1049 Datasheet
tza1049
Available stocks
Related parts for tza1049
tza1049 Summary of contents
Page 1
... DATA SHEET TZA1049 4-channel BTL driver for CD/DVD drives Product specification INTEGRATED CIRCUITS 2004 Mar 09 ...
Page 2
... CHARACTERISTICS 10 TEST AND APPLICATION INFORMATION 11 PACKAGE OUTLINE 2004 Mar 09 12 SOLDERING 12.1 Introduction to soldering surface mount packages 12.2 Reflow soldering 12.3 Wave soldering 12.4 Manual soldering 12.5 Suitability of surface mount IC packages for wave and reflow soldering methods 13 DATA SHEET STATUS 14 DEFINITIONS 15 DISCLAIMERS 2 Product specification TZA1049 ...
Page 3
... APPLICATIONS BTL driver for CD and DVD players. 3 GENERAL DESCRIPTION The TZA1049 is a four-channel BTL driver IC for driving motors and actuators in CD and DVD players. Two reference voltage outputs are also available for peripheral ICs such as servo and pick-up head drivers. The spindle motor control inputs to the IC can be either differential or single-ended ...
Page 4
... Mar 09 3.3 V GENERATOR 32.3 k MUTE 32 32 Fig.1 Block diagram. 4 Product specification 1 GENERATOR x1 2 RADOUTN x1 3 FOCOUTP 4 GND x1 5 FOCOUTN x1 6 RADOUTP TZA1049 SLOUTP x1 10 SLOUTN 11 GND x0.5 12 MOTOUTP x0.5 13 MOTOUTN mce478 TZA1049 ...
Page 5
... V bias voltage output 19 ground 20 bias voltage input 21 sled motor driver input 22 focus coil driver input 23 radial coil driver input 24 mute control input 25 1.8 V generator/regulator feedback voltage input 26 1.8 V generator/regulator output 27 3.3 V generator/regulator feedback voltage input 28 3.3 V generator/regulator output 5 Product specification TZA1049 DESCRIPTION ...
Page 6
... You must ensure that these pins are connected to an external ground. 7. The 1.65 V bias voltage output from pin VBIASOUT is derived from the internal 3.3 V generator/regulator, and will be affected by any variation in the 3.3 V generator/regulator voltage. 6 Product specification TZA1049 and pin GND and CC ...
Page 7
... 700 mV (p-p 4 note 1 ext 700 mV (p-p 4 note 1 ext 7 Product specification TZA1049 MIN. MAX. UNIT 13 +150 C MIN. TYP. MAX. UNIT 20 25 100 kHz 20 ...
Page 8
... For gain measurements, only the channel being tested is active, the others are inactive; see Fig.4. 2004 Mar 09 CONDITIONS MIN 400 560 700 mV (p-p 4 note 1 ext 3 Product specification TZA1049 TYP. MAX. UNIT 430 mA 600 mA 1.12 1.26 V/V 3.3 3 1.8 1 ...
Page 9
... TEST AND APPLICATION INFORMATION handbook, halfpage 70 70 1.6 mm glass epoxy board. At temperatures above power dissipation is de-rated at 13.6 mW/ C. amb Fig.3 Power dissipation as a function of ambient temperature. 2004 Mar ( 100 150 9 Product specification TZA1049 MCE472 200 T amb (˚C) ...
Page 10
... Fig.4 Gain test configuration. 10 Product specification TZA1049 GENERATOR x1 RADOUTN FOCOUTP GND FOCOUTN x1 6 RADOUTP TZA1049 SLOUTP SLOUTN GND 11 x0.5 MOTOUTP 12 8 x0.5 13 MOTOUTN mce480 12 V 220 F 8 ...
Page 11
... M motor 13 14 Fig.5 Spindle motor differential control application. 11 Product specification SLED FOCUS 18 COIL COIL SERVO/COIL DRIVER 17 SPINDLE 16 MOTOR1 SPINDLE 15 MOTOR2 MUTE FORWARD MICROCONTROLLER REVERSE MCE481 TZA1049 RADIAL COIL ...
Page 12
... sled M motor spindle M motor 13 14 Fig.6 Spindle motor single-ended application. 12 Product specification SLED FOCUS 18 COIL COIL SERVO/COIL DRIVER 17 SPINDLE 16 MOTOR1 15 MUTE FORWARD MICROCONTROLLER REVERSE MCE482 TZA1049 RADIAL COIL ...
Page 13
... Plastic or metal protrusions are not included. OUTLINE VERSION IEC SOP007 2004 Mar scale (1) ( 0.45 0.30 18.67 7.75 10.02 0.8 0.30 0.23 18.41 7.49 9.62 REFERENCES JEDEC JEITA 13 Product specification detail 1.0 1.1 0.089 0.4 EUROPEAN PROJECTION TZA1049 SOP007 ISSUE DATE 03-07-28 ...
Page 14
... Use a low voltage ( less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds 300 C. When using a dedicated tool, all other leads can be soldered in one operation within seconds between 270 and 320 C. 14 Product specification TZA1049 ...
Page 15
... However, the image sensor package can be mounted by the client on a flex foil by using a hot bar soldering process. The appropriate soldering profile can be provided on request. 9. Hot bar or manual soldering is suitable for PMFP packages. 2004 Mar 09 (1) (3) , TFBGA, (8) 15 Product specification TZA1049 SOLDERING METHOD WAVE REFLOW not suitable suitable (4) not suitable suitable suitable ...
Page 16
... Product specification TZA1049 DEFINITION These products are not Philips Semiconductors ...
Page 17
Philips Semiconductors – a worldwide company Contact information For additional information please visit http://www.semiconductors.philips.com. For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com. © Koninklijke Philips Electronics N.V. 2004 All rights are reserved. Reproduction in whole or in part is prohibited ...