at90ls4433 ATMEL Corporation, at90ls4433 Datasheet - Page 57

no-image

at90ls4433

Manufacturer Part Number
at90ls4433
Description
At90s4433 8-bit Avr Microcontroller With 4k Bytes Of In-system Programmable Flash
Manufacturer
ATMEL Corporation
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
at90ls4433-4AC
Manufacturer:
ATM
Quantity:
72
Part Number:
at90ls4433-4AI
Manufacturer:
HYNIX
Quantity:
14
Part Number:
at90ls4433-4AI
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
at90ls44334AC
Manufacturer:
ON
Quantity:
3 617
UART Control
UART I/O Data Register – UDR
UART Control and Status
Register A – UCSRA
1042H–AVR–04/03
The UDR Register is actually two physically separate registers sharing the same I/O
address. When writing to the register, the UART Transmit Data Register is written.
When reading from UDR, the UART Receive Data Register is read.
• Bit 7 – RXC: UART Receive Complete
This bit is set (one) when a received character is transferred from the Receiver Shift
Register to UDR. The bit is set regardless of any detected framing errors. When the
RXCIE bit in UCSRB is set, the UART Receive Complete interrupt will be executed
when RXC is set (one). RXC is cleared by reading UDR. When interrupt-driven data
reception is used, the UART Receive Complete Interrupt routine must read UDR in
order to clear RXC, otherwise a new interrupt will occur once the interrupt routine
terminates.
• Bit 6 – TXC: UART Transmit Complete
This bit is set (one) when the entire character (including the stop bit) in the Transmit
Shift Register has been shifted out and no new data has been written to UDR. This flag
is especially useful in half-duplex communications interfaces, where a transmitting appli-
cation must enter Receive mode and free the communications bus immediately after
completing the transmission.
When the TXCIE bit in UCSRB is set, setting of TXC causes the UART Transmit Com-
plete interrupt to be executed. TXC is cleared by hardware when executing the
corresponding interrupt handling vector. Alternatively, the TXC bit is cleared (zero) by
writing a logical “1” to the bit.
• Bit 5 – UDRE: UART Data Register Empty
This bit is set (one) when a character written to UDR is transferred to the Transmit Shift
Register. Setting of this bit indicates that the Transmitter is ready to receive a new char-
acter for transmission.
When the UDRIE bit in UCSRB is set, the UART Transmit Complete interrupt to be exe-
cuted as long as UDRE is set. UDRE is cleared by writing UDR. When interrupt-driven
data transmittal is used, the UART Data Register Empty Interrupt routine must write
UDR in order to clear UDRE, otherwise a new interrupt will occur once the interrupt rou-
tine terminates.
UDRE is set (one) during reset to indicate that the transmitter is ready.
Bit
$0C ($2C)
Read/Write
Initial Value
Bit
$0B ($2B)
Read/Write
Initial Value
MSB
RXC
R/W
R
7
0
7
0
R/W
TXC
R/W
6
0
6
0
UDRE
R/W
R
5
0
5
1
R/W
FE
R
4
0
4
0
R/W
OR
R
3
0
3
0
R/W
R
2
0
2
0
AT90S/LS4433
R/W
R
1
0
1
0
MPCM
LSB
R/W
R/W
0
0
0
0
UCSRA
UDR
57

Related parts for at90ls4433