at90ls4433 ATMEL Corporation, at90ls4433 Datasheet - Page 81

no-image

at90ls4433

Manufacturer Part Number
at90ls4433
Description
At90s4433 8-bit Avr Microcontroller With 4k Bytes Of In-system Programmable Flash
Manufacturer
ATMEL Corporation
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
at90ls4433-4AC
Manufacturer:
ATM
Quantity:
72
Part Number:
at90ls4433-4AI
Manufacturer:
HYNIX
Quantity:
14
Part Number:
at90ls4433-4AI
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
at90ls44334AC
Manufacturer:
ON
Quantity:
3 617
Port D as General Digital I/O
Alternate Functions of Port D
1042H–AVR–04/03
PDn, General I/O pin: The DDDn bit in the DDRD Register selects the direction of this
pin. If DDDn is set (one), PDn is configured as an output pin. If DDDn is cleared (zero),
PDn is configured as an input pin. If PDn is set (one) when configured as an input pin,
the MOS pull-up resistor is activated. To switch the pull-up resistor off, the PDn has to
be cleared (zero) or the pin has to be configured as an output pin.The port pins are tri-
stated when a reset condition becomes active, even if the clock is not running.
Table 27. DDDn Bits on Port D Pins
Note:
• AIN1 – Port D, Bit 7
AIN1, Analog Comparator Negative Input. When configured as an input (DDD7 is
cleared [zero]), and with the internal MOS pull-up resistor switched off (PD7 is cleared
[zero]), this pin also serves as the negative input of the On-chip Analog Comparator.
During Power-down mode, the Schmitt trigger of the digital input is disconnected. This
allows analog signals, which are close to V
out causing excessive power consumption.
• AIN0 – Port D, Bit 6
AIN0, Analog Comparator Positive Input. When configured as an input (DDD6 is cleared
[zero]), and with the internal MOS pull-up resistor switched off (PD6 is cleared [zero]),
this pin also serves as the positive input of the On-chip Analog Comparator. During
Power-down mode, the Schmitt trigger of the digital input is disconnected. This allows
analog signals, which are close to V
causing excessive power consumption.
• T1 – Port D, Bit 5
T1, Timer/Counter1 Counter Source. See the Timer description for further details
• T0 – Port D, Bit 4
T0: Timer/Counter0 Counter Source. See the Timer description for further details.
• INT1 – Port D, Bit 3
INT1, External Interrupt Source 1: The PD3 pin can serve as an external interrupt
source to the MCU. See the interrupt description for further details and how to enable
the source.
• INT0 – Port D, Bit 2
INT0, External Interrupt Source 0: The PD2 pin can serve as an external interrupt
source to the MCU. See the interrupt description for further details and how to enable
the source.
DDDn
0
0
1
1
1. n: 7,6..0, pin number.
PORTDn
0
1
0
1
Output
Output
Input
Input
I/O
Pull-up
Yes
No
No
No
(1)
CC
/2, to be present during Power-down without
CC
Comment
Tri-state (high-Z)
PDn will source current if ext. pulled low.
Push-pull Zero Output
Push-pull One Output
/2, to be present during Power-down with-
AT90S/LS4433
81

Related parts for at90ls4433