ftlf1621s1xcl Finisar Corporation., ftlf1621s1xcl Datasheet
ftlf1621s1xcl
Related parts for ftlf1621s1xcl
ftlf1621s1xcl Summary of contents
Page 1
... Single 3.3V power supply Low power dissipation <900mW typical Extended operating temperature range: -10°C to 70°C Finisar’s FTLF1621S1xCL Small Form Factor (SFF) transceivers are compatible with the Small Form Factor Multi-Sourcing Agreement (MSA) 48 LR-2 (SDH STM L-16.2) standards 3 specified in IEEE Std 802.3 , Fibre Channel FC-PI 13.0 ...
Page 2
... FTLF1621S1xCL 2x10 Pin SFF Product Specification – March 2006 I. Pin Descriptions Pin Symbol MS MS Mounting Studs for mechanical attachment. Chassis ground is internally isolated from circuit ground. Connection to chassis ground is recommended Receiver Power Monitor. This pin must be connected to a positive voltage supply (Vcc), preferably via a small resistor ...
Page 3
... FTLF1621S1xCL 2x10 Pin SFF Product Specification – November 2005 II. Absolute Maximum Ratings Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature Relative Humidity Lead Soldering Temperature/Time III. Electrical Characteristics Parameter Supply Voltage Supply Current Transmitter Input differential impedance Single ended data input swing ...
Page 4
... FTLF1621S1xCL 2x10 Pin SFF Product Specification – November 2005 IV. Optical Characteristics Parameter Transmitter Output Opt. Pwr: 9/125 SMF Optical Wavelength Spectral Width (-20dB) Optical Extinction Ratio Sidemode Suppression ratio Optical Rise/Fall Time Relative Intensity Noise Total Generated Transmitter Jitter (peak to peak) ...
Page 5
... FTLF1621S1xCL 2x10 Pin SFF Product Specification – November 2005 V. General Specifications Parameter Data Rate Bit Error Rate Max. Supported Link Length on 9/125 m SMF @ OC-48 Max. Supported Link Length on 9/125 m SMF @ 2X Fibre Channel Max. Supported Link Length on 9/125 m SMF @ Gigabit Ethernet Max. Supported Link Length on 9/125 m SMF @ OC-12 Max ...
Page 6
... FTLF1621S1xCL 2x10 Pin SFF Product Specification – November 2005 VIII. Analog Diagnostics Functions Parameter Transmitter Monitor photodiode current monitor Laser bias current monitor Receiver Received photocurrent Photodiode responsivity Applied voltage at PD pin Notes: 1. Pins 19 and 20 provide an analog voltage output proportional to the monitor photodiode current, per the following formula: I equivalent circuit ...
Page 7
... FTLF1621S1xCL 2x10 Pin SFF Product Specification – November 2005 IX. Mechanical Specifications Finisar’s OC-48/STM-16 Small Form Factor (SFF) transceivers comply with the standard dimensions defined by the Small Form Factor Multi-Sourcing Agreement (MSA). FTLF1621S1GCL – 2 pin version Finisar Corporation March 2006 Rev A ...
Page 8
... FTLF1621S1xCL 2x10 Pin SFF Product Specification – November 2005 FTLF1621S1HCL – 6 pin version Finisar Corporation March 2006 Rev Page 8 ...
Page 9
... FTLF1621S1xCL 2x10 Pin SFF Product Specification – November 2005 FTLF1621S1HCL – 6 pin version (Long EMI Shield) Finisar Corporation March 2006 Rev Page 9 ...
Page 10
... FTLF1621S1xCL 2x10 Pin SFF Product Specification – November 2005 X. PCB Layout and Bezel Recommendations Minimum Recommended Module-to-Module Spacing is 0.6 inches Finisar Corporation March 2006 Rev Page 10 ...
Page 11
... Note AN-2038: Finisar Implementation of RoHS Compliant Transceivers:. Finisar Corporation, January 21, 2005. (*) Neither IEEE 802.3 nor FC-PI 13.0 specifies a 1550nm DFB single mode interface. The FTLF1621S1xCL complies with these standards except for receiver sensitivity, ER and transmit output power. See Section IV for details. XII. ...
Page 12
... FTLF1621S1xCL 2x10 Pin SFF Product Specification – November 2005 Finisar Corporation March 2006 Rev Page 12 ...