at78c7005 ATMEL Corporation, at78c7005 Datasheet

no-image

at78c7005

Manufacturer Part Number
at78c7005
Description
Spindle/vcm Motorcontroller/drivers
Manufacturer
ATMEL Corporation
Datasheet
Features
Description
The AT78C7005 is a CMOS monolithic device that integrates Spindle and VCM con-
trollers as well as power stages into one chip. The device operates from 3.3V or 5V
power supply. The AT78C7005 is designed for a small-form-factor hard disk drive
application.
A precision low-voltage detection circuit monitors the power supply and initiates VCM
retract at voltage fault condition. A 3-line serial port interface with read back capability
provides interface to the microprocessor.
The Spindle driver features a transconductance amplifier, a current sense amplifier,
power output drivers, sequencer, internal delay/masking logic, Spindle brake circuit,
FLL, and charge-pump for locking the spindle to the programmed rotational speed.
The VCM driver features a transconductance amplifier, differential input current sense
amplifier, ramp load/unload capability, and power output amplifier.
Operates from Single Supply: 3.3V or 5V
Small Footprint 64-Pin TQFP Package or Flip Chip
Precision Low-voltage Monitor Circuitry for the Power Supply
Master Power on Reset
Serial Port Interface with Read-back Capability
Over-temperature Protection/Warning
Shock Sensor Signal Processing
On-chip 1.8V, 2.5V and -3V Regulators
Low Power Consumption, 9 mA in Normal Run Mode
Spindle Driver
VCM Driver
Available in a Variety of Packages Depending on Customer Requirements
– Commutator is Driven by a FLL for High Immunity to Jitter
– Programmable 10-bit DAC
– Adjustable Slew Rate Control
– External Startup Capability
– 1.0A Current Capability with R
– Digital Commutation Delay and Blanking
– Programmable Delay from BEMF Zero Crossing
– External INDEX Signal for Spin Lock
– Active Spindle Braking Capability
– 0.4A Current Capability with R
– Programmable 14-bit DAC
– Ramp Load/Unload Capability with 10-bit ADC
– Power-off Retract with 9V Charge-pump
– Programmable VCM Current Controlled by Sense Resistor
on
on
= 1Ω
= 1.5Ω
Note: This is a summary document. A complete document
is available under NDA. For more information, please con-
tact your local Atmel sales office.
Spindle/
VCM Motor
Controller/
Drivers
AT78C7005
Summary
3432BS–NETST–5/04

Related parts for at78c7005

at78c7005 Summary of contents

Page 1

... Available in a Variety of Packages Depending on Customer Requirements Description The AT78C7005 is a CMOS monolithic device that integrates Spindle and VCM con- trollers as well as power stages into one chip. The device operates from 3. power supply. The AT78C7005 is designed for a small-form-factor hard disk drive application ...

Page 2

... Figure 1. AT78C7005 Block Diagram SYSCLK FLL VREF XIN XOUT SHOCKIN VREF F40 SHOCKB VC1.8 V1.8 VC2.5 V2.5 VC3.3 V3.3 VREF RREF RTH CRET PORB DRET CRET RETO AT78C7005 2 MUX CLK Prescaler FLL UP DN CHP Comp PWM Voltage Limiter OTA 10 bit DAC 3 bit DAC Comp 1 ...

Page 3

Packaging Information 64A1 – TQFP PIN 0˚~7˚ L Notes: 1. This package conforms to JEDEC reference MS-026, Variation ACD. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is 0.25 mm per side. Dimensions ...

Page 4

... Fax: (81) 3-3523-7581 Disclaimer: Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein ...

Related keywords