w49f002u Winbond Electronics Corp America, w49f002u Datasheet - Page 4

no-image

w49f002u

Manufacturer Part Number
w49f002u
Description
256k X 8 Cmos Flash Memory
Manufacturer
Winbond Electronics Corp America
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
w49f002u-12B
Manufacturer:
WINBOND
Quantity:
5 670
Part Number:
w49f002u-12B
Manufacturer:
WINBOND
Quantity:
5 670
Part Number:
w49f002u-12B
Manufacturer:
Winbond
Quantity:
11
Part Number:
w49f002u-12B
Manufacturer:
DENSO
Quantity:
6 223
Part Number:
w49f002u-12B
Manufacturer:
WINBOND
Quantity:
46
Part Number:
w49f002u-12B
Manufacturer:
WINBOND
Quantity:
673
Part Number:
w49f002u12B
Manufacturer:
WINBOND
Quantity:
4 050
Part Number:
w49f002uP12B
Manufacturer:
WINBOND/华邦
Quantity:
20 000
Part Number:
w49f002uP12B
Manufacturer:
WINBOND
Quantity:
2 522
Company:
Part Number:
w49f002uP12B
Quantity:
1 300
operation if the boot block programming lockout feature is not activated. Once the boot block lockout
feature is activated, the whole chip erase function will erase the two main memory blocks and the two
parameter blocks but not the boot block. The device will automatically return to normal read mode
after the erase operation. Data polling and/or Toggle Bits can be used to detect end of erase cycle.
Sector Erase Operation
There are four sectors: two main memory blocks and two parameters blocks which can be erased
individually by initiating a six-byte command code sequence. Sector address is latched on the falling
edge of WE signal in the sixth cycle while the data input "30(hex)" is latched at the rising edge of WE
in this cycle. After the command loading cycle, the device enters the internal sector erase mode,
which is automatically timed and will be completed as fast as 100 mS (typical). The host system does
not require to provide any control or timing during this operation. The device will automatically return
to normal read mode after the erase operation. Data polling and/or Toggle Bits can be used to detect
the end of erase cycle.
When different sector address is loaded in the sixth cycle for sector erase command, the
correspondent sectors will be erased automatically; that these sections will be erased independedntly.
For detail sector to be erased information, please refer to the Table of Command Definition.
Program Operation
The W49F002U is programmed on a byte-by-byte basis. Program operation can only change logical
data "1" to logical data "0". The erase operation (changed entire data in two main memory blocks and
two parameter blocks and/or boot block from "0" to "1") is needed before programming.
The program operation is initiated by a 4-byte command code sequence (see Command Codes for
Byte Programming). The device will internally enter the program operation immediately after the byte-
program command is entered. The internal program timer will automatically time-out (50 S max. -
T
be used to detect end of program cycle.
Hardware Data Protection
The integrity of the data stored in the W49F002U is also hardware protected in the following ways:
(1) Noise/Glitch Protection: A WE pulse of less than 15 nS in duration will not initiate a write cycle.
(2) V
(3) Write Inhibit Mode: Forcing OE low, CE high, or WE high will inhibit the write operation. This
(4) V
Data Polling (DQ
The W49F002U includes a data polling feature to indicate the end of a program or erase cycle.
When the W49F002U is in the internal program or erase cycle, any attempt to read DQ
byte loaded will receive the complement of the true data. Once the program or erase cycle is
completed, DQ
and become logical "1" or true data when the erase cycle has been completed.
BP
). Once completed, the device returns to normal read mode. Data polling and/or Toggle Bits can
2.5V typical.
prevents inadvertent writes during power-up or power-down periods.
5 mS before any write (erase/program) operation.
DD
DD
power-on delay: When V
Power Up/Down Detection: The programming operation is inhibited when V
7
will show the true data. Note that DQ
7
)- Write Status Detection
DD
has reached its sense level, the device will automatically time-out
- 4 -
7
will show logical "0" during the erase cycle,
W49F002U
DD
is less than
7
of the last

Related parts for w49f002u