110MB102A1 CTS [CTS Corporation], 110MB102A1 Datasheet

110MB102A1

Manufacturer Part Number

110MB102A1

Description

Commercial 3/4inch (19mm) Diameter, 1 1/2 and 2 watt Wirewound Variable Resistor

Manufacturer

CTS [CTS Corporation]

Datasheet

1.110MB102A1.pdf (3 pages)

Current page: 1 of 3
Download datasheet (958Kb)

Commercial

Diameter, 1

Watt Wirewound

Variable Resistors

Electrical and Mechanical Specifications

Resistance Range

Resistance Tolerance

Power Rating, Watts

Voltage Rating

Resistance Taper

Minimum Resistance

Resistance Taper

Incorporated Fixed Resistor

Features

1 - 3

CTS Electronic Components

• Inexpensive design

• Open construction

• Four mounting styles

• Incorporated fixed resistor available

• Available with nylon knob

• Interchangeable mounting with

• RoHS compliant

1 ohm through 10K ohms (linear taper)

Standard:±20%

Special:±5% or 10%

2 watts @ 55°C derated to no load @ 105°C,

1.5 watts @ 55°C derated to no load @ 105°C,

Determined by resistance value and wattage rating

Standard:Linear taper only

At ends of rotation: 1% or 1 ohm, whichever is greater

None

A fixed resistor can be incorporated in the Series 110

" (19mm)

CTS Series 115 preset potentiometer

mounted on steel panel

mounted on bakelite panel

at the end of CW or CCW rotation to a minimum of 10%

of the total resistance. The rotation is shortened by an

amount proportional to the ratio of the fixed resistor to

the total resistance. Available at extra cost.

and 2

Series 110

Angle of Rotation

Resistor Adjustment

Mounting Types Available

Rotational Torque

Terminals

246°±5°without fixed resistor stop

Standard Cross Slot: Provided in drive plate for screwdriver

Special Molded Knob: Available at extra cost secured to

Type 110:

Type XPC - 110: Vertically mounted on printed circuit board

Type 111:

Type 112:

Terminals at end of CW or CCW rotation may be omitted.

adjustment.

drive plate cross slot.

Refer to terminals on all types by numbers 1 and 3 as

indicated on line drawings.

to 10 inch ounces (36 – 720 gf-cm)

Solder or clinch-ear mounted

Snap-in mounting

Eyelet or rivet mounting

www.ctscorp.com

9/30/06

Related parts for 110MB102A1

110MB102A1 Summary of contents

Page 1

Commercial / " (19mm Diameter and 2 2 Watt Wirewound Variable Resistors Features • Inexpensive design • Open construction • Four mounting styles • Incorporated fixed resistor available • Available with nylon knob • ...

Page 2

Type 110, Solder or Clinch-Ear Mounted, Long Terminal Length 246° 57° 57° END C.C.W. ROT. NO. 1 TERM 19.94 .785 TYPE M110, Solder Mounted, Medium Terminal Length 19.9±0.4 .783±.016 rot 246° end c.w. rot. no. 1 terminal 57° 57° TYPE ...

Page 3

Type 111, Snap-In Mounted END C.C.W ROT NO.1 TERM 57° 21.59 19.94 246° .785 57° END C.W ROT NO.3 TERM SCREWDRIVER ADJUSTMENT SLOT Type 112, Eyelet or Rivet Mounted 240° ROT. 31.75 1.25 25.4 1.000 19.94 .785 9.53 .375 END ...

Related keywords

110MB102A1 datasheet
110MB102A1 data sheet
110MB102A1 pdf datasheet
110MB102A1 component
110MB102A1 part
110MB102A1 distributor
110MB102A1 RoHS
110MB102A1 datasheet download