lc78602ne Sanyo Semiconductor Corporation, lc78602ne Datasheet
lc78602ne
Related parts for lc78602ne
lc78602ne Summary of contents
Page 1
... Ordering number : EN6021 Overview The LC78602NE CMOS IC implements compact disc player signal processing, servo control, LED display, key input acquisition, and remote controller processing without requiring control by a separate microcontroller. The basic functions provided include demodulation of the EFM signal from the optical pickup, deinterleaving, error ...
Page 2
... Synchronization detection EFM demodulation CLV digital servo Subcode separator QCRC Servo commander System control LC78602NE Package Dimensions unit: mm 3159-QFP64E [LC78602NE] RAM address generator Interpolation and muting Bilingual support circuit C1 and C2 error detection and correction Flag processing Digital attenuator 8 oversampling digital filters ...
Page 3
... Output voltage Allowable power dissipation Operating temperature Storage temperature Allowable Operating Ranges –20 to +75°C, V Parameter Supply voltage High-level input voltage Low-level input voltage Input level Operating frequency range Crystal oscillator frequency LC78602NE = Symbol Conditions V max OUT ...
Page 4
... Total harmonic distortion THD+N LCHO, RCHO Dynamic range DR LCHO, RCHO Signal-to-noise ratio S/N LCHO, RCHO Crosstalk CT LCHO, RCHO Note: Measured in normal speed playback mode with the Sanyo 1-bit D/A converter block reference circuit. LC78602NE = 4 Applicable pins Conditions , ...
Page 5
... D/A Converter Output Block Reference Circuit Oscillator element: 16.9344 MHz Oscillator The following oscillator elements are recommended CSA-309 < pF> (Citizen Watch Co., Ltd.) element CSA16.93MXZ040 ( pF) (Murata Mfg. Co., Ltd.) CSA16.93MXZ0C3 (built-in capacitor) (Murata Mfg. Co., Ltd.) LC78602NE AD725D (Manufactured by Shibasoku Ltd.) Analog output Left channel (right channel) No. 6021-5/11 ...
Page 6
... RMTSL3 I/O switches to the high level. Therefore, applications that will set this pin high must connect an external pull-up resistor to this pin. LC78602NE Function Internal VCO control phase comparator output Internal VCO ground. This pin must be connected PDO output current adjustment resistor connection ...
Page 7
... Crystal oscillator circuit power supply DD 63 *RES I IC reset input. Applications must set this pin low temporarily when power is first applied. 64 DRF I DRF input Note: The same potential must be connected to all the power supply pins (V LC78602NE Function , VV , L/RV , and Pin state during reset ...
Page 8
... Sample Application Circuit Note: This circuit is an example of typical connections used with the LC78602NE, but is not a complete circuit, i.e. certain peripheral components and circuits have been omitted. Contact your Sanyo representative for detailed information on this circuit. ...
Page 9
... Applications must first apply a reset to this IC after power is applied. Since pin states and register contents that are not defined by the reset operation may change over time from the states in early versions due to long term variations across lots, applications should not depend on these values. LC78602NE level, and do not lower the voltage below ...
Page 10
... This IC is specifically designed for use in CD players, and as such its specifications differ from those of general- purpose product standard logic ICs. We recommend system debugging using the end product system itself and adopting failsafe system design if required by the application. LC78602NE pin as possible also appropriate to insert capacitors of about DD ...
Page 11
... SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of December, 1998. Specifications and information herein are subject to change without notice. LC78602NE PS No. 6021-11/11 ...