cxa3092n Sony Electronics, cxa3092n Datasheet
cxa3092n
Related parts for cxa3092n
cxa3092n Summary of contents
Page 1
... Read/Write Amplifier for Thin Film Head of Hard Disk Drive For the availability of this product, please contact the sales office. Description The CXA3092N is a Read/Write Amplifier for the thin film head of hard disk drive and designed to handle channel heads. Features • ...
Page 2
... H1X DRIVER AMP 5 H1Y 6 H2X DRIVER AMP 7 H2Y 8 H3X DRIVER AMP 9 H3Y POWER 10 V ON/OFF CC DETECTOR MODE CONTROL WRITE CURRENT SOURCE AMP HEAD SELECT IC PROTECTOR WRITE UNSAFE DETECTOR —2— CXA3092N 20 XCS 19 R RDY 16 RDX 15 HS0 14 HS1 13 WDX 12 WDY 11 WUS/SE ...
Page 3
... H3X 7 9 H3Y WUS/ WDY 13 WDX 13 Equivalent circuit V CC GND V CC GND V CC GND —3— CXA3092N Description Head. 4 channels provided power supply. Write unsafe detection output / Servo Enable signal input. Differential P-ECL write data input. ...
Page 4
... GND V CC 2.1V GND V CC 2.1V GND —4— CXA3092N Description Head select signal input. Selects one of 4 heads according to Table 2. Read Amplifier output. A setting resistor for the write current value is connected between this pin and GND. Read/Write signal input At “High” : Read, at “ ...
Page 5
... CXA3092N ...
Page 6
... CXA3092N ...
Page 7
... CXA3092N ...
Page 8
... CXA3092N ...
Page 9
... L =0 µ the time required for Write current to reach from the same time required reach 10 % from µ —9— CXA3092N =15 mA, L (Head W H Refer to Fig Fig. 4 Min. Typ. Max. Unit 5.8 6.8 Vp-p 0.2 0.4 µs 0.3 0.5 µs ...
Page 10
... I 1 SG2 33 0.1µ SG1 1k 1k AMP 1µ 1µ 3. 1µH 1µH —10— CXA3092N 1µ SG3 5.1k PG SG4 ...
Page 11
... Timing Chart 1 WDX WDY R RDX RDY Timing Chart 2 WDX WDY 10% WUS T SA2 50% 90% 10 90% Fig. 3 90% 90% 10 50% Fig. 4 —11— CXA3092N 50 10 90% T SA1 50% ...
Page 12
... While maintaing step (2) and (3) above make R/W low, placing the device in servo write mode. R/W WUS/SE HS0 HS1 L X See Table See Table Table 1. Mode selection HS0 HS1 Head Table 2. Head selection to WUS/SE. SEH —12— CXA3092N Mode Write Read Servo Write X Idle ...
Page 13
... ON/OFF detector, in which case the recording and playback functions are prohibited. When V CC HS0 Table 3. Head selection in Servo Write mode rises above, VTH, the prohibition of these functions is released. HS1 Head —13— CXA3092N 10 MHz) falls below the CC ...
Page 14
... Application circuits shown are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits or for any infringement of third party patent and other right due to same. PULSE DETECTOR 1µH 1µH —14— CXA3092N 1µ 5. 1µH 5V ...
Page 15
... VFB must be more than 2 V. When V frequency becomes more than 1 MHz. The normal operating area of write unsafe detection circuit is changed by head inductance, head DC resistance, write current and other < possible that Write unsafe detection maximum FB —15— CXA3092N =1.4V GND ...
Page 16
... L =1 µ µ = 50% 50% 50 Pin 18 —16— CXA3092N V =5V, Ta=25 °C CC Min. Typ. Max. Unit 10 pF 260 350 440 0.6 1 0.2 mAp-p –0.5 0 ...
Page 17
... ON OFF 3.8 3.6 – Ambient temperature Ta [°C] Normalized write current vs. Ambient temperature Ta=25°C 1.04 R =3.3k WC 1.02 1 0.98 0.96 –25 0 Ambient temperature Ta [°C] Normalized read amplifier voltage gain vs. Ambient temperature Ta=25°C 1.04 1.02 1 0.98 0.96 –25 0 Ambient temperature Ta [°C] —17— CXA3092N V = =3. = ...
Page 18
... NOTE : PALLADIUM PLATING This product uses PdPPF (Palladium Pre-Plated Lead Frame). 20PIN SSOP(PLASTIC) 2.0MAX 0.3 ± 0.1 M 0.13 0.05MIN DETAIL A PACKAGE STRUCTURE PACKAGE MATERIAL LEAD TREATMENT SSOP-20P-L122 LEAD MATERIAL SSOP020-P-0300 PACKAGE MASS —18— CXA3092N 0.15 10°MAX EPOXY RESIN PALLADIUM PLATING COPPER ALLOY 0.15g ...