IR205 EXTECH [Extech Instruments Corporation.], IR205 Datasheet

IR205

Manufacturer Part Number

IR205

Description

Pocket InfraRed Thermometer

Manufacturer

EXTECH [Extech Instruments Corporation.]

Datasheet

1.IR205.pdf (1 pages)

Current page: 1 of 1
Download datasheet (188Kb)

Pocket InfraRed Thermometer

Introduction

Congratulations on your purchase of Extech’s IR201 Pocket InfraRed

Thermometer. This device allows the user to take non-contact temperature

measurements simply by pointing the meter and pressing a button. Features

include: Laser pointer, Max/Min, Adjustable emissivity, Lock ON and HI

audible alarm. This meter is shipped fully tested and calibrated and, with

proper use, will provide years of reliable service.

IR Measurements

Taking Measurements

Laser Pointer

Set Feature

Display

Controls

Model IR205

User's Manual

Point the meter toward the object being measured, then press and hold

the MEASURE button. The meter will turn ON and take readings (SCAN).

Read the measured temperature on the LCD. When the MEASURE

button is released, the last measurement is HELD in the display for

approximately 8 seconds before the meter shuts down.

While pressing the MEASURE button, Press the LASER button to turn

the laser pointer ON or OFF.

While in the MEAS mode;

Press the SET button to gain access to the following features in

sequence.

Release the MEAS button when the feature needed is selected

Press the Laser button to change the selection or value

Press the MEAS button to confirm the selection.

#1: Max/Min:

#2: °C/°F:

#3: Є ▲:

#4: Є ▼:

#5:

#6: Hi ▲:

#7: HI ▼:

#8:

IR Sensor

Laser Pointer

MEASURE Button

Battery Compartment (rear)

LASER button

SET button

Display

Displays only the maximum or minimum value

during a measurement scan.

Select measurement units

Increase emissivity value.

Decrease emissivity value

Lock On/Off (Overrides auto-power off)

Increase High Alarm value

Decrease High Alarm value

Audible Alarm On/Off:

Specifications

Measurement considerations:

Distance to spot diagram

Battery Replacement

A flashing display indicates that the AAA batteries which power the meter

have weakened. Open the battery compartment on the rear of the meter,

replace the batteries and close the compartment.

Warranty

EXTECH INSTRUMENTS CORPORATION warrants this instrument to be free of defects in

parts and workmanship for one year from date of shipment (a six month limited warranty

applies on sensors and cables). If it should become necessary to return the instrument for

service during or beyond the warranty period, contact the Customer Service Department at

(781) 890-7440 for authorization. A Return Authorization (RA) number must be issued

before any product is returned to Extech. The sender is responsible for shipping charges,

freight, insurance and proper packaging to prevent damage in transit. This warranty does

not apply to defects resulting from action of the user such as misuse, improper wiring,

operation outside of specification, improper maintenance or repair, or unauthorized

modification. Extech specifically disclaims any implied warranties or merchantability or

fitness for a specific purpose and will not be liable for any direct, indirect, incidental or

consequential damages. Extech's total liability is limited to repair or replacement of the

product. The warranty set forth above is inclusive and no other warranty, whether written or

oral, is expressed or implied.

Display

Power off

Laser power

Operating Temperature

Operating Humidity

Power Supply

Weight

Ranges(Resolution)

Accuracy

Recommended measuring

distance

Emissivity settings

Distance to Target Ratio

Size

If the surface of an object to be measured is covered with frost, dust or

other materials, surface cleaning must be performed before accurate

measurements can be made.

If the surface of an object to be measured is highly reflective with a very

low emissivity value, apply masking tape or apply flat black paint to the

surface to raise to improve the accuracy of the measurement.

The object being measured should be larger than the spot size as

illustrated in the distance to spot diagram.

-31 to 518°F/ -35 to 270°C (1°F/1°C)

± (2.5% of reading + 3°F or 2°C)

(-4° to 518°F / -20° to 270°C):

± 10°F or 5°C

(-31° to -4°F / -35° to -20°C)

2” to 36” / 5cm to 91cm

0.1 to 1.00 adjustable

6:1

3 ½ -digit (2000 count) LCD display

Automatic shutoff after approx. 8 seconds

Laser power less than 1mW (red)

32 to 122°F (0 to 50°C)

Max. 80% RH

2 x AAA battery

2.7 oz. / 76g

3.7 x 2 x 1" (94 x 51 x 25 mm)

6”(15cm)

12”(30cm)

1”(2cm)

18”(48cm)

2”(5cm)

IR205 V1.0 3/06

3”(8cm)

Related parts for IR205

Related keywords

IR205 datasheet
IR205 data sheet
IR205 pdf datasheet
IR205 component
IR205 part
IR205 distributor
IR205 RoHS
IR205 datasheet download