SPECIFICATIONS
Contact
Note:
Remarks
* Specifications will vary with foreign standards certification ratings.
*
*
*
*
*
*
*
*
*
ORDERING INFORMATION
Arrangement
Initial contact resistance, max.
(By voltage drop 6 V DC 1 A)
Contact material
Rating
Nominal
operating
power
Expected
life (min.
operations)
1
2
3
4
5
6
7
8
9
Contact arrangement
1This value can change due to the switching frequency, environmental conditions,
Measurement at same location as "Initial breakdown voltage" section.
By resistive method, nominal voltage applied to the coil; contact carrying current:
2 A.
Nominal voltage applied to the coil, excluding contact bounce time.
Nominal voltage applied to the coil, excluding contact bounce time without diode.
Half-wave pulse of sine wave: 6 ms; detection time: 10 s.
Half-wave pulse of sine wave: 6 ms.
Detection time: 10 s.
Refer to 4. Conditions for operation, transport and storage mentioned in Cautions
for use (Page 178).
As for the applicable range of continuous carrying current against temperature,
please refer to "Maximum value of continuous carrying current" chart. (Page 175)
and desired reliability level, therefore it is recommended to check this with the ac-
tual load.
The maximum ambient temperature allows for coil temperature rise at maximum
allowable coil voltage.
1: 1 Form C
Nominal switching capacity
(resistive load)
Max. Switching power
(resistive load)
Max. switching voltage
Max. switching current
Min. switching capacity
Single side stable
1 coil latching
2 coil latching
Mechanical (at 180 cpm)
Electrical
(at 20 cpm)
Nil: Single side stable
L: 1 coil latching
L2: 2 coil latching
Operating function
10.6
.417
2 A 30 V DC
resistive
EX. TK
.354
1
9.0
ULTRA LOW PROFILE 2 AMP.
POLARIZED RELAY
1
5 10
.157
4.0
140 mW (1.5 to 12 V DC)
100 mW (1.5 to 12 V DC)
200 mW (1.5 to 9 V DC)
10
Gold-clad silver alloy
270 mW (24 V DC)
150 mW (24 V DC)
250 mW (12 V DC)
400 mW (24 V DC)
8
10 A 10 mV DC
7
(Single side stable)
Nil: Standard PC board terminal
H: Self-clinching terminal
2 A 30 V DC
(1 or 2 coil latching)
220 V DC
1 Form C
L2
50 m
60 W
mm
2 A
10
5
Terminal shape
inch
H
12V
FEATURES
• Low profile 4 mm .157 inch height
• High contact capacity: 2 A
• Surge withstand voltage between contact and coil: 2,500 V
(Bellcore rating)
Characteristics
Initial insulation resistance*
Initial
breakdown
voltage
FCC surge voltage between open
contacts (10 160 s)
Surge voltage between contacts
and coil (2 10 s) [Bellcore]
Temperature rise*
Operate time [Set time]*
Release time [Reset time]*
(at 20 C)
Shock resistance
Vibration
resistance
Conditions for
operation, trans-
port and storage*
(Not freezing and
condensing at low
temperature)
Unit weight
Coil voltage (DC)
1.5, 3, 4.5, 5, 6,
9, 12, 24V
Between open
contacts
Between contact and
coil
8
2
(at 20 C)
TK-RELAYS
Functional*
Destructive*
Functional*
Destructive
Ambient
temperature*
Humidity
3
(at 20 C)
4
1
5
7
6
9
196 m/s
294 m/s
Min. 1,000 M
Max. 3 ms (Approx. 1.5 ms)
double amplitude of 3.3 mm
[Max. 3 ms (Approx. 1 ms)]
[Max. 3 ms (Approx. 1 ms)]
(Detection current: 10 mA)
(Detection current: 10 mA)
double amplitude of 5 mm
Max. 2 ms (Approx. 1 ms)
Min. 1,000 m/s
1,500 Vrms for 1 min.
Min. 750 m/s
Approx. 1 g
750 Vrms for 1 min.
–40 F to +185 F
–40 C to +85 C
2
2
5 to 85% R.H.
{20G}, 10 to 55 Hz at
{30G}, 10 to 55 Hz at
Max. 50 C
1,500 V
2,500 V
(at 500 V DC)
.035 oz.
2
2
{75 G}
{100 G}
TESTING
173