MAX9152ESE Maxim, MAX9152ESE Datasheet
MAX9152ESE
Available stocks
Related parts for MAX9152ESE
MAX9152ESE Summary of contents
Page 1
... Inputs Accept LVDS/LVPECL Signals o LVDS Output Rated for 75Ω and 100Ω Loads o Pin-Programmable Differential Output Resistance o Pin-Compatible Upgrade to DS90CP22 (SO Package) o Available in 16-Pin TSSOP Package (Half the Size of SO) PART MAX9152ESE MAX9152EUE Pin Configuration appears at end of data sheet. Applications EN0 SEL0 IN0+ IN0- ...
Page 2
... TSSOP (derate 9.4mW/°C above +70°C) .........755mW Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability ...
Page 3
LVDS/LVPECL-to-LVDS ELECTRICAL CHARACTERISTICS (continued +3.0V to +3.6V, NC/RSEL = open for input voltage ( IN+ IN +3.3V, ...
Page 4
LVDS/LVPECL-to-LVDS Crosspoint Switch AC ELECTRICAL CHARACTERISTICS (continued +3.0V to +3.6V, NC/RSEL = open for 0.15V EN_ = high, SEL0 = low, SEL1 = high, differential input ...
Page 5
LVDS/LVPECL-to-LVDS +3.3V 100Ω, NC/RSEL = high pattern +1.2V +25°C, unless otherwise noted PEAK-TO-PEAK OUTPUT JITTER vs. DATA RATE ...
Page 6
LVDS/LVPECL-to-LVDS Crosspoint Switch PIN NAME 1, 2 SEL1, SEL0 LVCMOS/LVTTL Logic Inputs. Allow the switch to be configured as a mux, repeater, or splitter IN0+, IN0- LVDS/LVPECL Differential Input Power-Supply Input. ...
Page 7
LVDS/LVPECL-to-LVDS IN0 IN0- IN1 IN1+ SEL_ OUT_+ OUT_- EN0 = EN1 = HIGH ) − IN_+ IN_- Figure 2. Input to Rising Edge Select Setup, Hold, ...
Page 8
... IN_- should be pulled to GND with 10kΩ Devices can be cascaded to make larger switches. 3V Total propagation delay and total jitter should be con- 1.5V sidered to determine the maximum allowable switch 0 size. Three MAX9152s are needed to make a 2 input x t PZH 4 output crosspoint switch with two device propagation VOH 50% delays ...
Page 9
LVDS/LVPECL-to-LVDS IN_ IN_+ t PLHD V OUT_ OUT_+ 80% 80% 50 20% t LHT ...
Page 10
LVDS/LVPECL-to-LVDS Crosspoint Switch 5V 82Ω 82Ω 50Ω 5V 10kΩ PECL 50Ω IN_+ 100Ω IN_- 33Ω 33Ω Figure 9. PECL to LVDS Level Conversion Network Pin Configuration TOP VIEW SEL1 1 SEL0 2 INO+ 3 MAX9152 INO- ...
Page 11
LVDS/LVPECL-to-LVDS ______________________________________________________________________________________ Crosspoint Switch Package Information 11 ...
Page 12
... LVDS/LVPECL-to-LVDS Crosspoint Switch Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © ...