SAA7826HL Philips Semiconductors, SAA7826HL Datasheet - Page 85

no-image

SAA7826HL

Manufacturer Part Number
SAA7826HL
Description
CD audio decoder/ digital servo and filterless DAC with integrated pre-amp and laser control
Manufacturer
Philips Semiconductors
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
SAA7826HL
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
SAA7826HL/E
Manufacturer:
PHILIPS
Quantity:
14
Part Number:
SAA7826HL/E
Quantity:
29
Part Number:
SAA7826HL/E/M1A,55
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Part Number:
SAA7826HL/M1A,557
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Part Number:
SAA7826HL/S5
Manufacturer:
NXP
Quantity:
36
Part Number:
SAA7826HL/S5
Manufacturer:
NXP
Quantity:
8 000
Part Number:
SAA7826HL/S6
Manufacturer:
NXP
Quantity:
7 052
Philips Semiconductors
16 SOLDERING
16.1
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “Data Handbook IC26; Integrated Circuit Packages”
(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface
mount IC packages. Wave soldering can still be used for
certain surface mount ICs, but it is not suitable for fine pitch
SMDs. In these situations reflow soldering is
recommended.
16.2
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Driven by legislation and environmental forces the
worldwide use of lead-free solder pastes is increasing.
Several methods exist for reflowing; for example,
convection or convection/infrared heating in a conveyor
type oven. Throughput times (preheating, soldering and
cooling) vary between 100 and 200 seconds depending
on heating method.
Typical reflow peak temperatures range from
215 to 270 C depending on solder paste material. The
top-surface temperature of the packages should
preferably be kept:
Moisture sensitivity precautions, as indicated on packing,
must be respected at all times.
16.3
Conventional single wave soldering is not recommended
for surface mount devices (SMDs) or printed-circuit boards
with a high component density, as solder bridging and
non-wetting can present major problems.
2003 Oct 01
below 220 C (SnPb process) or below 245 C (Pb-free
process)
– for all BGA and SSOP-T packages
– for packages with a thickness
– for packages with a thickness < 2.5 mm and a
below 235 C (SnPb process) or below 260 C (Pb-free
process) for packages with a thickness < 2.5 mm and a
volume < 350 mm
CD audio decoder, digital servo and filterless
DAC with integrated pre-amp and laser control
volume
Introduction to soldering surface mount
packages
Reflow soldering
Wave soldering
350 mm
3
so called small/thin packages.
3
so called thick/large packages.
2.5 mm
85
To overcome these problems the double-wave soldering
method was specifically developed.
If wave soldering is used the following conditions must be
observed for optimal results:
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Typical dwell time of the leads in the wave ranges from
3 to 4 seconds at 250 C or 265 C, depending on solder
material applied, SnPb or Pb-free respectively.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
16.4
Fix the component by first soldering two
diagonally-opposite end leads. Use a low voltage (24 V or
less) soldering iron applied to the flat part of the lead.
Contact time must be limited to 10 seconds at up to
300 C.
When using a dedicated tool, all other leads can be
soldered in one operation within 2 to 5 seconds between
270 and 320 C.
Use a double-wave soldering method comprising a
turbulent wave with high upward pressure followed by a
smooth laminar wave.
For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint
– smaller than 1.27 mm, the footprint longitudinal axis
The footprint must incorporate solder thieves at the
downstream end.
For packages with leads on four sides, the footprint must
be placed at a 45 angle to the transport direction of the
printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
longitudinal axis is preferred to be parallel to the
transport direction of the printed-circuit board;
must be parallel to the transport direction of the
printed-circuit board.
Manual soldering
Product specification
SAA7826

Related parts for SAA7826HL