MC68HC711PH8 Motorola, MC68HC711PH8 Datasheet - Page 75
MC68HC711PH8
Manufacturer Part Number
MC68HC711PH8
Description
High-density Complementary Metal Oxide Semiconductor (HCMOS) Microcomputer Unit
Manufacturer
Motorola
Datasheet
1.MC68HC711PH8.pdf
(264 pages)
- Current page: 75 of 264
- Download datasheet (2Mb)
PH8.DS03/Modes+mem
3.4.3
Because the CONFIG register is implemented with EEPROM cells, use EEPROM procedures to
erase and program this register. The procedure for programming is the same as for programming
a byte in the EEPROM array, except that the CONFIG register address is used. CONFIG can be
programmed or erased (including byte erase) while the MCU is operating in any mode, provided
that PTCON in BPROT is clear. To change the value in the CONFIG register, complete the
following procedure. Do not initiate a reset until the procedure is complete.
CONFIG — System configuration register
For a description of the bits contained in the CONFIG register refer to Section 3.3.2.1.
CONFIG is made up of EEPROM cells and static working latches. The operation of the MCU is
controlled directly by these latches and not the EEPROM byte. When programming the CONFIG
register, the EEPROM byte is accessed. When the CONFIG register is read, the static latches are
accessed.
These bits can be read at any time. The value read is the one latched into the register from the
EEPROM cells during the last reset sequence. A new value programmed into this register is not
readable until after a subsequent reset sequence.
On the MC68HC711PH8 , and on the MC68HC11PH8 if selected by a mask option, the ROMON
bit can be written at any time if MDA = 1 (expanded mode or special test mode). It cannot be
written in bootstrap mode, and is forced to a logic one in single chip mode.
Other bits in CONFIG can be written at any time if SMOD = 1 (bootstrap or special test mode). If
SMOD = 0 (single chip or expanded mode), these bits can only be written using the EEPROM
programming sequence, and none of the bits is readable or active until latched via the next reset.
FREEZ is only active in expanded user mode.
MC68HC11PH8
ConÞguration control (CONFIG)
1) Erase the CONFIG register.
2) Program the new value to the CONFIG address.
3) Initiate reset.
CONFIG register programming
OPERATING MODES AND ON-CHIP MEMORY
Address
—this line does not form part of the document—
$003F ROMAD FREEZ CLK4X PAREN NOSEC NOCOP ROMON EEON xxxx xxxx
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
[DS97 v 4.1] 08/Apr/97@13:55
bit 1
bit 0
MOTOROLA
on reset
State
TPG
3-29
10
12
13
14
15
11
1
2
3
4
5
6
7
8
9
Related parts for MC68HC711PH8
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Motorola, Inc [VOLTAGE REGULATOR]
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
3N2046367254 MOTOROLA SC (XSTRS/R F)
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
MOTOROLA POWERPC 603e MICROPROCESSOR
Manufacturer:
Motorola
Part Number:
Description:
Motorola Semiconductor Datasheet Library
Manufacturer:
Motorola
Part Number:
Description:
SWITCHMODE Schottky Power Rectifier(POWERTAP III Package)
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
SWITCHMODE Schottky Power Rectifirer
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
Hybrid Power Module
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
Hybrid Power Module
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
Search -----> MTE53N50E
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
Hybrid Power Module
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
Hybrid Power Module
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
SCHOTTKY BARRIER RECTIFIER 200 AMPERES 60 VOLT
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
NPN SILICON POWER DARLINGTON TRANSISTOR
Manufacturer:
Motorola
Datasheet: