ISL54205EVAL1Z INTERSIL [Intersil Corporation], ISL54205EVAL1Z Datasheet - Page 14

• Manufacturer Part Number: ISL54205EVAL1Z
• Description: MP3/USB 2.0 High Speed Switch with Negative Signal Handling
• Manufacturer: INTERSIL [Intersil Corporation]

Thin Dual Flat No-Lead Plastic Package (TDFN)
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
(DATUM A)
NX (b)
INDEX
AREA
5
(DATUM B)
SECTION "C-C"
6
8
INDEX
NX L
AREA
SEATING
6
PLANE
A
C
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
1
N
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
BOTTOM VIEW
(A1)
SIDE VIEW
N-1
TOP VIEW
e
(Nd-1)Xe
For information regarding Intersil Corporation and its products, see www.intersil.com
2
REF.
D2
D
D2/2
14
FOR ODD TERMINAL/SIDE
C C
e
7
NX b
C L
2X
A3
5
E2/2
0.10
8
0.10
E
B
A
NX k
E2
C
2X
M
A
TERMINAL TIP
//
0.10
C
L1
0.10
A
0.08
C B
B
C
C
9 L
ISL54205A
L10.3x3A
10 LEAD THIN DUAL FLAT NO-LEAD PLASTIC PACKAGE
NOTES:
1. Dimensioning and tolerancing conform to ASME Y14.5-1994.
2. N is the number of terminals.
3. Nd refers to the number of terminals on D.
4. All dimensions are in millimeters. Angles are in degrees.
5. Dimension b applies to the metallized terminal and is measured
6. The configuration of the pin #1 identifier is optional, but must be
7. Dimensions D2 and E2 are for the exposed pads which provide
8. Nominal dimensions are provided to assist with PCB Land
9. Compliant to JEDEC MO-229-WEED-3 except for D2
SYMBOL
between 0.15mm and 0.30mm from the terminal tip.
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
improved electrical and thermal performance.
Pattern Design efforts, see Intersil Technical Brief TB389.
dimensions.
A1
A3
D2
E2
Nd
A
D
E
N
b
e
k
L
0.70
0.20
2.95
2.25
2.95
1.45
0.25
0.25
MIN
-
MILLIMETERS
NOMINAL
0.50 BSC
0.20 REF
0.75
0.25
2.30
1.50
0.30
3.0
3.0
10
5
-
-
MAX
0.80
0.05
0.30
3.05
2.35
3.05
1.55
0.35
-
December 7, 2006
Rev. 3 3/06
NOTES
5, 8
7, 8
7, 8
FN6342.1
8
2
3
-
-
-
-
-
-
-