MC68HC705 MOTOROLA [Motorola, Inc], MC68HC705 Datasheet - Page 126

no-image

MC68HC705

Manufacturer Part Number
MC68HC705
Description
HCMOS Microcontroller Unit
Manufacturer
MOTOROLA [Motorola, Inc]
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MC68HC705
Manufacturer:
ON
Quantity:
66
Part Number:
MC68HC705
Manufacturer:
MOTOROLA
Quantity:
9 066
Part Number:
MC68HC705B16
Manufacturer:
MOT
Quantity:
5 510
Part Number:
MC68HC705B16
Manufacturer:
OMRON
Quantity:
5 510
Part Number:
MC68HC705B16
Manufacturer:
MOT
Quantity:
1 000
Part Number:
MC68HC705B16
Manufacturer:
MOTOROLA/摩托罗拉
Quantity:
20 000
Part Number:
MC68HC705B16CFN
Manufacturer:
MOT
Quantity:
5 510
Part Number:
MC68HC705B16CFN
Manufacturer:
MOT
Quantity:
2 132
Part Number:
MC68HC705B16CFN
Manufacturer:
FREESCALE
Quantity:
20 000
Part Number:
MC68HC705B16CFNE
Manufacturer:
FREESCALE
Quantity:
2 512
Part Number:
MC68HC705B16NCFN
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
MC68HC705B16NCFNE
Manufacturer:
FREESCALE
Quantity:
2 513
Part Number:
MC68HC705B5B
Manufacturer:
MOTOROLA
Quantity:
20 000
Serial Communications Interface (SCI)
Technical Data
126
Character Length — The receiver can accommodate either 8-bit
or 9-bit data. The state of the M bit in SCI control register 1
(SCCR1) determines character length. When receiving 9-bit data,
bit R8 in SCCR1 is the ninth bit (bit 8).
Character Reception — During reception, the receive shift register
shifts characters in from the PD0/RDI pin. The SCI data register
(SCDR) is the read-only buffer between the internal data bus and
the receive shift register.
After a complete character shifts into the receive shift register, the
data portion of the character is transferred to the SCDR, setting
the receive data register full (RDRF) flag. The RDRF flag can be
used to generate an interrupt.
Receiver Wakeup — So that the MCU can ignore transmissions
intended only for other receivers in multiple-receiver systems, the
MCU can be put into a standby state. Setting the receiver wakeup
enable (RWU) bit in SCI control register 2 (SCCR2) puts the MCU
into a standby state during which receiver interrupts are disabled.
Either of two conditions on the PD0/RDI pin can bring the MCU out
of the standby state:
– Idle input line condition — If the PD0/RDI pin is at logic 1 long
– Address mark — If a logic 1 occurs in the most significant bit
The state of the WAKE bit in SCCR1 determines which of the two
conditions wakes up the MCU.
Receiver Noise Immunity — The data recovery logic samples
each bit 16 times to identify and verify the start bit and to detect
noise. Any conflict between noise detection samples sets the
noise flag (NF) in the SCSR. The NF bit is set at the same time
that the RDRF bit is set.
Serial Communications Interface (SCI)
enough for 10 or 11 logic 1s to shift into the receive shift
register, receiver interrupts are again enabled.
position of a received character, receiver interrupts are again
enabled.
MC68HC705C8A — Rev. 2.0
MOTOROLA

Related parts for MC68HC705