ADM205 AD [Analog Devices], ADM205 Datasheet
ADM205
Related parts for ADM205
ADM205 Summary of contents
Page 1
... W making them ideally suited for battery powered equipment. The ADM205 does not require any external components and is par- ticularly useful in applications where printed circuit board space is critical. The ADM213 has an active-low shutdown and an ...
Page 2
... MIN MAX Min Typ Max Units Test Conditions/Comments 5 9 Volts All Transmitter Outputs Loaded with Ground Load, ADM206, ADM211, ADM213 Load, ADM205, ADM207, ADM208 0 Load, ADM209 3 Load ADM209 Only 0 2 ...
Page 3
... OUT TTL/CMOS OUTPUTS * **INTERNAL 5k PULL-DOWN RESISTOR ON EACH RS-232 INPUT Figure 2. ADM205 Typical Operating Circuit –3– ADM205–ADM211/ADM213 Temperature Range ADM207 ADM207AN – +85 C ADM207AR – +85 C ADM207ARS – +85 C ADM211 ADM211AR – +85 C ADM211ARS – ...
Page 4
... ADM205–ADM211/ADM213 T3 1 OUT T1 2 OUT T2 3 OUT OUT ADM206 Top View T1 7 (Not to Scale) IN GND C1 C1– 12 Figure 3. ADM206 DIP/SOIC/SSOP Pin Configuration 10 C1+ +5V TO +10V 0.1 F VOLTAGE 6.3V 12 C1– DOUBLER C2+ 13 +10V TO –10V 0.1 F VOLTAGE 16V ...
Page 5
... IN TTL/CMOS OUTPUTS RS-232 ** INPUTS INTERNAL 400k PULL-UP RESISTOR ON EACH TTL/CMOS INPUT **INTERNAL 5k PULL-DOWN RESISTOR ON EACH RS-232 INPUT Figure 10. ADM209 Typical Operating Circuit –5– ADM205–ADM211/ADM213 OUT GND OUT ...
Page 6
... ADM205–ADM211/ADM213 1 T3 OUT T1 2 OUT T2 3 OUT OUT ADM211 IN Top View 8 R1 OUT (Not to Scale GND C1 C1– 14 Figure 11. ADM211 SOIC/SSOP Pin Configuration 12 C1+ +5V TO +10V 0.1 F VOLTAGE 16V 14 DOUBLER C1– C2+ 15 +10V TO – ...
Page 7
... SD/SD Shutdown Input. Active high on ADM205, ADM206, ADM211. Active low on ADM213. With SD = high on the ADM205, ADM206, ADM211, the charge pump is disabled, the receiver outputs are placed in a high impedance state and the driver outputs are turned off. With SD low on the ADM213, the charge pump is disabled, the driver outputs are turned off and all receivers except R4 and R5 are placed in a high impedance state ...
Page 8
... ADM205–ADM211/ADM213–Typical Performance Characteristics — mA OUT Figure 15. Charge Pump V+, V– vs. Current 500 1000 1500 CAPACITIVE LOAD – pF Figure 16. Transmitter Slew Rate vs. Load Capacitance V– 3.0 Figure 17. Transmitter Output Voltage vs. V ...
Page 9
... W. The ADM205 is designed for applications where space saving is important as the charge pump capacitors are molded into the package. The ADM209 includes only a negative charge pump converter and are intended for applications where a positive available ...
Page 10
... The ADM205, ADM209, ADM211, and ADM213 feature an enable input used to enable or disable the receiver outputs. The enable input is active low on the ADM205, ADM209, ADM211 and active-high on the ADM213. Refer to Tables II and III. When disabled, all receiver outputs are placed in a high imped- ance state ...
Page 11
... BSC 0.005 (0.127) 1. LEAD NO. 1 IDENTIFIED BY A DOT. 2. LEADS WILL BE EITHER TIN PLATED OR SOLDER DIPPED IN ACCORDANCE WITH MIL-M-38510 REQUIREMENTS –11– ADM205–ADM211/ADM213 24-Lead Cerdip (Q-24 0.295 (7.493) MAX 12 12 1.290 (32.77) MAX 0.180 (4.572) MAX ...
Page 12
... ADM205–ADM211/ADM213 28-Lead SOIC (R-28 PIN 0.096 (2.44) 0.708 (18.02) 0.089 (2.26) 0.696 (17.67) 0.01 (0.254) 0.019 (0.49) 0.05 (1.27) 0.006 (0.15) BSC 0.014 (0.35) 1. LEAD NO. IDENTIFIED BY A DOT. 2. SOICLEADS WILL BE EITHER TIN PLATED OR SOLDER DIPPED IN ACCORDANCE WITH MIL-M-38510 REQUIREMENTS. OUTLINE DIMENSIONS Dimensions shown in inches and (mm). 28 0.299 (7.6) 0.291 (7.39) ...