FT245RL-2000 FTDI [Future Technology Devices International Ltd.], FT245RL-2000 Datasheet
FT245RL-2000
Related parts for FT245RL-2000
FT245RL-2000 Summary of contents
Page 1
Future Technology Devices International Ltd FT245R USB FIFO IC The FT245R is a USB to parallel FIFO interface with the following advanced features: Single chip USB to parallel FIFO bidirectional data transfer interface. Entire USB protocol handled on the chip. ...
Page 2
... For driver installation, please refer to 1.2 Part Numbers Part Number FT245RQ-xxxx FT245RL-xxxx Note: Packaging codes for xxx is: -Reel: Taped and Reel, (SSOP is 2,000pcs per reel, QFN is 6,000pcs per reel). - Tube: Tube packing, 47pcs per tube (SSOP only) - Tray: Tray packing, 490pcs per tray (QFN only) For example: FT245RQ-Reel is 6,000pcs taped and reel packing Copyright © ...
Page 3
USB Compliant The FT245R is fully compliant with the USB 2.0 specification and has been given the USB-IF Test-ID (TID) 40680005. Copyright © 2010 Future Technology Devices International Limited Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.10 ...
Page 4
FT245R Block Diagram VCC 3.3 Volt LDO 3V3OUT Regulator USB Transceiver USBDP Serial Interface with Integrated Series USBDM Resistors and 1.5K Pull-up USB DPLL OSCO (optional) Internal Clock 12MHz Multiplier OCSI Oscillator (optional) TEST GND Figure 2.1 FT245R Block ...
Page 5
Table of Contents 1 Typical Applications ........................................................................ 2 1.1 Driver Support .................................................................................... 2 1.2 Part Numbers...................................................................................... 2 1.3 USB Compliant .................................................................................... 3 2 FT245R Block Diagram .................................................................... 4 3 Device Pin Out and Signal Description ............................................ 7 3.1 28-LD SSOP ...
Page 6
Solder Reflow Profile ..................................................................... 32 11 Contact Information ................................................................... 33 Appendix A - References ............................................................................ 34 Appendix B - List of Figures and Tables ..................................................... 35 Appendix C - Revision History .................................................................... 37 Copyright © 2010 Future Technology Devices ...
Page 7
... USBDP Description USB Data Signal Plus, incorporating internal series resistor and 1.5kΩ pull up resistor to 3.3V. USB Data Signal Minus, incorporating internal series resistor. Document No.: FT_000052 Clearance No.: FTDI VCCIO 20 VCC 16 USBDM 15 USBDP FT245RL RESET OSCI 28 OSCO RXF# TXE# 17 3V3OUT RD# ...
Page 8
Pin No. Name Type 4 VCCIO PWR 7, 18, GND PWR 21 17 3V3OUT Output 20 VCC PWR 25 AGND PWR Table 3.2 Power and Ground Group Pin No. Name Type RESET# Input 26 TEST ...
Page 9
Pin No. Name Type 11 D3 I/O 12 PWREN# Output 13 RD# Input 14 WR Input 22 TXE# Output 23 RXF Output Table 3.4 FIFO Interface Group (see note 3) Notes: 1. The minimum operating voltage VCC must be +4.0V ...
Page 10
QFN-32 Package Figure 3.2 QFN-32 Package Pin Out and schematic symbol 3.4 QFN-32 Package Signal Description Pin No. Name Type Description USB Data Signal Plus, incorporating internal series resistor and 1.5kΩ pull up resistor 14 USBDP I/O to +3.3V. ...
Page 11
Pin No. Name Type Description +1.8V to +5.25V supply for the FIFO Interface group pins (2, 3, 6,7,8,9,10 11, 21, 22, 30,31,32). In USB bus powered designs connect this pin to 3V3OUT to drive out at +3.3V levels, or connect ...
Page 12
Pin Name Type Description No I/O FIFO Data Bus Bit I/O FIFO Data Bus Bit I/O FIFO Data Bus Bit 3 Goes low after the device is configured by USB, then high ...
Page 13
FT245R FIFO READ Timing Diagrams RXF# RD# T3 D[7...0] Figure 3.3 FIFO Read Cycle Time Description T1 RD# Active Pulse Width T2 RD# to RD# Pre-Charge Time T3 RD# Active to Valid Data* Valid Data Hold Time from RD# ...
Page 14
FT245R FIFO WRITE Timing Diagrams TXE# WR D[7...0] Figure 3.4 FIFO Write Cycle Time Description T7 WR Active Pulse Width Pre-Charge Time Valid data setup to WR falling T9 edge* Valid Data Hold Time from ...
Page 15
Function Description The FT245R is a USB to parallel FIFO interface device which simplifies USB to FIFO designs and reduces external component count by fully integrating an external EEPROM, USB termination resistors and an integrated clock circuit which requires ...
Page 16
Functional Block Descriptions The following paragraphs detail each function within the FT245R. Please refer to the block diagram shown in Figure 2.1 Internal EEPROM. The internal EEPROM in the FT245R is used to store USB Vendor ID (VID), Product ...
Page 17
... Parameter Storage Temperature Floor Life (Out of Bag) At Factory Ambient (30°C / 60% Relative Humidity) Ambient Temperature (Power Applied) MTTF FT245RL MTTF FT245RQ VCC Supply Voltage DC Input Voltage – USBDP and USBDM DC Input Voltage – High Impedance Bidirectionals DC Input Voltage – All Other Inputs DC Output Current – ...
Page 18
DC Characteristics DC Characteristics (Ambient Temperature = -40°C to +85°C) Parameter Description VCC Operating Supply VCC1 Voltage VCC Operating Supply VCC1 Voltage VCCIO Operating VCC2 Supply Voltage Operating Supply Icc1 Current Operating Supply Icc2 Current 3V3 3.3v regulator output ...
Page 19
Parameter Description Voh Output Voltage High Vol Output Voltage Low Input Switching Vin Threshold Input Switching VHys Hysteresis Table 5.5 FIFO I/O Pin Characteristics (VCCIO = +2.8V, Standard Drive Level) Parameter Description Voh Output Voltage High Vol Output Voltage Low ...
Page 20
Parameter Description Voh Output Voltage High Vol Output Voltage Low Input Switching Vin Threshold Input Switching VHys Hysteresis Table 5.9 FIFO I/O Pin Characteristics (VCCIO = +2.8V, High Drive Level) Parameter Description Voh Output Voltage High Vol Output Voltage Low ...
Page 21
Parameter Description Driver Output UDrvZ Impedance Table 5.12 USB I/O Pin (USBDP, USBDM) Characteristics Note 1: Driver output impedance includes the internal USB series termination resistors on USBDP and USBDM pins 6.1 EEPROM Reliability Characteristics The internal 1024 Bit EEPROM ...
Page 22
... USB Power Configurations The following sections illustrate possible USB power configurations for the FT245R. The illustrations have omitted pin numbers for ease of understanding since the pins differ between the FT245RL and FT245RQ package options. All USB power configurations illustrated apply to both package options for the FT245R device. Please refer to Section 3 for the package option pin-out and signal descriptions ...
Page 23
Self Powered Configuration Figure 7.2 Self Powered Configuration Figure 7.2 illustrates the FT245R in a typical USB self powered configuration. A USB self powered device gets its power from its own power supply, VCC, and does not draw current ...
Page 24
USB Bus Powered with Power Switching Configuration P-Channel Power MOSFET Ferrite Bead 10nF SHIELD GND 100nF 4.7uF Figure 7.3 Bus Powered with Power Switching Configuration A requirement of USB bus powered applications, is ...
Page 25
PWREN# gets its VCC from VCCIO. For designs using 3V3 logic, ensure VCCIO is not powered down using the external logic. In this case use the +3V3OUT. 7.4 USB Bus Powered with Selectable External Logic Supply Ferrite Bead 1 ...
Page 26
... Application Examples The following sections illustrate possible applications of the FT245R. The illustrations have omitted pin numbers for ease of understanding since the pins differ between the FT245RL and FT245RQ package options. 8.1 USB to MCU FIFO Interface Ferrite Bead 10nF 5 SHIELD GND ...
Page 27
Using the External Oscillator The FT245R defaults to operating using its own internal oscillator. This requires that the device is powered with VCC (min)=+4.0V. This supply voltage can be taken from the USB VBUS. Applications which require using an ...
Page 28
Internal EEPROM Configuration Following a power-on reset or a USB reset the FT245R will scan its internal EEPROM and read the USB configuration descriptors stored there. The default factory programmed values of the internal EEPROM are shown in Table ...
Page 29
... Figure 10.1 SSOP-28 Package Dimensions The FT245RL is supplied in a RoHS compliant 28 pin SSOP package. The package is lead (Pb) free and uses a „green‟ compound. The package is fully compliant with European Union directive 2002/95/EC. This package is nominally 5.30mm x 10.20mm body (7.80mm x 10.20mm including pins). The pins are ...
Page 30
QFN-32 Package Dimensions Indicates Pin # 1 ( Laser Marked ) Central Heat Sink Area 0. 500 0.250 +/-0.050 Pin # 200 Note: The pin # connected internally to the device’s central heat sink ...
Page 31
QFN-32 Package Typical Pad Layout Optional GND Connection 0.200 Min Figure 10.3 Typical Pad Layout for QFN-32 Package 10.4 QFN-32 Package Typical Solder Paste Diagram Figure 10.4 Typical Solder Paste Diagram for QFN-32 Package Copyright © 2010 Future Technology ...
Page 32
Solder Reflow Profile The FT245R is supplied in Pb free 28 LD SSOP and QFN-32 packages. The recommended solder reflow profile for both package options is shown Max S T Min S ...
Page 33
Contact Information Head Office – Glasgow, UK Future Technology Devices International Limited Unit 1, 2 Seaward Place, Centurion Business Park Glasgow G41 1HH United Kingdom Tel: +44 (0) 141 429 2777 Fax: +44 (0) 141 429 2758 E-mail (Sales) ...
Page 34
Appendix A - References Useful Application Notes http://www.ftdichip.com/Documents/AppNotes/AN232R-01_FT232RBitBangModes.pdf http://www.ftdichip.com/Documents/AppNotes/AN_107_AdvancedDriverOptions_AN_000073.pdf http://www.ftdichip.com/Documents/AppNotes/AN232R-02_FT232RChipID.pdf http://www.ftdichip.com/Documents/AppNotes/AN_121_FTDI_Device_EEPROM_User_Area_Usage.pdf http://www.ftdichip.com/Documents/AppNotes/AN_120_Aliasing_VCP_Baud_Rates.pdf http://www.ftdichip.com/Documents/AppNotes/AN_100_Using_The_FT232_245R_With_External_Osc(FT_ 000067).pdf http://www.ftdichip.com/Resources/Utilities/AN_126_User_Guide_For_FT232_Factory%20test%20utility. pdf http://www.ftdichip.com/Documents/AppNotes/AN232B-05_BaudRates.pdf http://www.ftdichip.com/Documents/InstallGuides.htm Copyright © 2010 Future Technology Devices International Limited Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.10 Clearance No.: FTDI# 39 ...
Page 35
Appendix B - List of Figures and Tables List of Figures Figure 2.1 FT245R Block Diagram ................................................................................................... 4 Figure 3.1 SSOP Package Pin Out and Schematic Symbol ................................................................... 7 Figure 3.2 QFN-32 Package Pin Out and schematic symbol .............................................................. 10 ...
Page 36
Table 5.11 RESET# and TEST Pin Characteristics ............................................................................ 20 Table 5.12 USB I/O Pin (USBDP, USBDM) Characteristics ................................................................. 21 Table 5.13 EEPROM Characteristics ............................................................................................... 21 Table 5.14 Internal Clock Characteristics ....................................................................................... 21 Table 5.15 OSCI, OSCO Pin Characteristics – see ...
Page 37
Appendix C - Revision History Version 0.90 Initial Datasheet Created Version 0.94 Revised Pre-release datasheet Version 1.00 Full datasheet released Version 1.02 Minor revisions to datasheet released Version 1.03 Manufacturer ID added to default EEPROM data Version 1.04 Buffer sizes ...