HC5515CP INTERSIL [Intersil Corporation], HC5515CP Datasheet
HC5515CP
Related parts for HC5515CP
HC5515CP Summary of contents
Page 1
... This process feature makes the HC5515 ideally suited for use in harsh outdoor environments. Ordering Information TEMP. o PART NUMBER RANGE ( C) PACKAGE HC5515CM PLCC HC5515CP PDIP HC5515IM - PLCC HC5515IP - PDIP Block Diagram RING RELAY RINGRLY ...
Page 2
Absolute Maximum Ratings Temperature, Humidity Storage Temperature Range . . . . . . . . . . . . . . . . -65 Operating Temperature Range ...
Page 3
Electrical Specifications 39k , R D number references in the figures refer to the 28 lead PLCC package. (Continued) PARAMETER LONGITUDINAL CURRENT LIMIT (TIP/RING) Off-Hook (Active) On-Hook (Standby 368 TIP RSN ...
Page 4
Electrical Specifications 39k , R D number references in the figures refer to the 28 lead PLCC package. (Continued) PARAMETER Standby TIP-RING Open Loop Metallic Voltage, V 4-WIRE TRANSMIT PORT ...
Page 5
Electrical Specifications 39k , R D number references in the figures refer to the 28 lead PLCC package. (Continued) PARAMETER 4-Wire to 2-Wire GRX = (( )(300k))/(-3)(600) TR1 TR2 Where ...
Page 6
Electrical Specifications 39k , R D number references in the figures refer to the 28 lead PLCC package. (Continued) PARAMETER RING TRIP DETECTOR (DT, DR) Offset Voltage Input Bias Current Input Common-Mode Range Input ...
Page 7
Electrical Specifications 39k , R D number references in the figures refer to the 28 lead PLCC package. (Continued) PARAMETER 4-Wire Port BAT -48V SUPPLY +5V SUPPLY -5V SUPPLY R ...
Page 8
I TIP TIP RING I RING HC5515 V = -48V 23mA, R BAT L 0 SATURATION GUARD VOLTAGE -10 CONSTANT CURRENT RESISTIVE FEED FEED REGION -20 -30 -40 SATURATION GUARD VOLTAGE -50 0 1.2K LOOP RESISTANCE ( ) ...
Page 9
The value of R calculated using Equation ------------------------------------------------------------------------------------------------------------------------------- -------------- - 17300 DC1 ...
Page 10
I M TIP RING For applications where the 2-wire impedance (Z Equation 15) is chosen to equal the ...
Page 11
Cases 2 and 3 illustrate the longitudinal loop current. The definition of a longitudinal loop current is a common mode current, that flows either out of or into tip and ring simultaneously. Longitudinal currents in the on-hook state result in ...
Page 12
TIP BAT RING RINGRLY RING RELAY FIGURE 18. RING TRIP CIRCUIT FOR BATTERY BACKED RINGING Longitudinal Impedance The feedback loop described in Figure ...
Page 13
Ringing State ( The ring relay driver and the ring trip detector are activated. Both the tip and ring line drive amplifiers are powered down. Both tip and ring are disconnected from the line via ...
Page 14
Notes 2. Overload Level (Two-Wire port) - The specified at the 2-wire port (V ) with the signal source at the TR0 4-wire receive port ( DCMET increase the amplitude of E until 1% THD is measured ...
Page 15
E = -10dBm, 1.0kHz signal computed using the following equation log ( vary amplitude -40dBm to +3dBm, 4 -55dBm to -40dBm and compare to -10dBm reading. ...
Page 16
Pin Descriptions (Continued) PLCC PDIP SYMBOL 20 22 HPR RING side of AC/DC separation capacitor C loop current. The other end HPT TIP side of AC/DC separation capacitor C current. The other end ...
Page 17
Application Circuit BAT PTC R F1 TIP D 3 PTC NOTE 31 RING Surgector RINGING +5V RELAY 90V ) BAT RMS ...