AT27BV010-70JI ATMEL [ATMEL Corporation], AT27BV010-70JI Datasheet
AT27BV010-70JI
Related parts for AT27BV010-70JI
AT27BV010-70JI Summary of contents
Page 1
... Atmel’s innovative design techniques provide fast speeds that rival 5V parts while keeping the low power consumption supply accessed in less than 70 ns. With a typical power draw of only MHz and V = 3V, the AT27BV010 consumes less than one fifth the power of a standard 5V CC Pin Configurations Pin Name ...
Page 2
... Description (Continued) EPROM. Standby mode supply current is typically less than 3V. The AT27BV010 simplifies system design and stretches battery lifetime even further by eliminating the need for power supply regulation. The AT27BV010 is available in industry standard JEDEC- approved one-time programmable (OTP) plastic PLCC and TSOP packages ...
Page 3
... A9 which is set gled low (V and high (V 6.5V CC AT27BV010 Supply Voltage with 1. Minimum voltage is -0.6V dc which may undershoot to -2.0V for pulses of less than 20 ns. Maximum out- put pin voltage 0.75V dc which may be ex- CC ceeded if certain precautions are observed (consult application notes) and which may overshoot to +7 ...
Page 4
... Input High Voltage IH V Output Low Voltage OL V Output High Voltage OH Notes must be applied simultaneously with or before and removed simultaneously with or after V PP AT27BV010 3-26 AT27BV010 -70 -90 0°C - 70°C 0°C - 70°C -40°C - 85°C -40°C - 85°C 2.7V to 3.6V 2.7V to 3.6V 5V 10% 5V 10% Condition ...
Page 5
... This parameter is only sampled and is not 100% tested. 5. Output float is defined as the point when data is no longer driven after the falling after the address OE . AT27BV010 AT27BV010 -70 -90 -12 -15 Min Max Min Max Min Max Min Max 70 90 120 70 90 120 50 ...
Page 6
... R F Pin Capacitance ( MHz 25°C) Typ OUT Note: 1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested. AT27BV010 3-28 (1) Max Units Output Test Load Note 100 pF including jig capacitance. Conditions V ...
Page 7
... Output High Voltage OH V Supply Current CC I CC2 (Program and Verify) V Supply PP I PP2 Current V A9 Product Identification Voltage ID (1) and 3. When programming the AT27BV010, a 0.1 F capacitor is IL required across V voltage transients. = 13.0 0.25V Test Conditions 2 -400 ...
Page 8
... Device Type Note: 1. The AT27BV010 has the same Product Identification Code as the AT27C010. Both are programming compatible. AT27BV010 3-30 Rapid Programming Algorithm = 13.0 0.2V A 100 s PGM pulse width is used to program. The ad- dress is set to the first location raised to 13.0V. Each address is first programmed ...
Page 9
... Lead, Plastic J-Leaded Chip Carrier (PLCC) 32T 32 Lead, Plastic Thin Small Outline Package (TSOP) Ordering Code Package AT27BV010-70JC AT27BV010-70TC AT27BV010-70JI AT27BV010-70TI AT27BV010-90JC AT27BV010-90TC AT27BV010-90JI AT27BV010-90TI AT27BV010-12JC AT27BV010-12TC AT27BV010-12JI AT27BV010-12TI AT27BV010-15JC AT27BV010-15TC AT27BV010-15JI AT27BV010-15TI Package Type AT27BV010 Operation Range ...