TOP242R POWERINT [Power Integrations, Inc.], TOP242R Datasheet - Page 23

• Manufacturer Part Number: TOP242R
• Description: TOPSwitch -GX Family Extended Power, Design Flexible, EcoSmart, Integrated Off-line Switcher
• Manufacturer: POWERINT [Power Integrations, Inc.]

A High Efficiency, 250 W, 250 – 380 VDC Input Power Supply
The circuit shown in figure 43 delivers 250 W (48 V @ 5.2 A)
at 84% efficiency using a TOP249 from a 250 to 380 VDC
input. DC input is shown, as typically at this power level a
p.f.c. boost stage would preceed this supply, providing the DC
input (C1 is included to provide local decoupling). Flyback
topology is still useable at this power level due to the high
output voltage, keeping the secondary peak currents low enough
so that the output diode and capacitors are reasonably sized.
In this example the TOP249 is at the upper limit of its power
capability and the current limit is set to the internal maximum
by connecting the X pin to SOURCE. However, line sensing
is implemented by connecting a 2 MΩ resistor from the L pin
to the DC rail. If the DC input rail rises above 450 VDC, then
TOPSwitch-GX will stop switching until the voltage returns to
normal, preventing device damage.
Due to the high primary current, a low leakage inductance
transformer is essential. Therefore, a sandwich winding with
a copper foil secondary was used. Even with this technique
the leakage inductance energy is beyond the power capability
of a simple Zener clamp. Therefore, R2, R3 and C6 are added
in parallel to VR1. These have been sized such that during
normal operation very little power is dissipated by VR1, the
leakage energy instead being dissipated by R2 and R3.
Figure 43. 250 W, 48 V Power Supply using TOP249.
+250 - 380 VDC
0V
PERFORMANCE SUMMARY
Output Power:
Line Regulation:
Load Regulation:
Efficiency:
Ripple:
No Load Consumption:
22 F
400 V
C1
P6KE200
1/2 W
VR1
2 M
R1
250 W
1%
5%
85%
100 mV pk-pk
1.4 W (300 VDC)
68 k
2 W
R2
BYV26C
68 k
2 W
R3
D1
D
S
4.7 nF
1 kV
C6
CONTROL
CONTROL
X
L
TOPSwitch-GX
2.2 nF Y1
T1
F
0.1 F
50 V
C3
C7
C
TOP249Y
U1
However, VR1 is essential to limit the peak drain voltage
during start-up and/or overload conditions to below the 700 V
rating of the TOPSwitch-GX MOSFET.
The secondary is rectifed and smoothed by D2 and C9, C10
and C11. Three capacitors are used to meet the secondary ripple
current requirement. Inductor L2 and C12 provide switching
noise filtering.
A simple Zener sensing chain regulates the output voltage. The
sum of the voltage drop of VR2, VR3 and VR4 plus the LED
drop of U2 gives the desired output voltage. Resistor R6
limits LED current and sets overall control loop DC gain.
Diode D4 and C14 provide secondary soft-finish, feeding
current into the CONTROL pin prior to output regulation and
thus ensuring that the output voltage reaches regulation at start-
up under low line, full load conditions. Resistor R9 provides a
discharge path for C14. Capacitor C13 and R8 provide control
loop compensation and are required due to the gain associated
with such a high output voltage.
Sufficient heat sinking is required to keep the TOPSwitch-GX
device below 110 °C when operating under full load, low line
and maximum ambient temperature. Airflow may also be
required if a large heat sink area is not acceptable.
D2
1N4148
47 F
6.8
D2
MUR1640CT
10 V
C3
R4
560 F
63 V
C9
1 F
50 V
C4
560 F
63 V
C10
BZX79B22
BZX79B12
BZX79B12
All resistor 1/8 W 5% unless
otherwise stated.
VR2 22 V
VR3 12 V
VR4 12 V
150 nF
LTV817A
63 V
C13
U2
100
560 F
R6
63 V
C11
3 H 8A
56
R8
L2
TOP242-250
68 F
63 V
C12
D4
1N4148
22 F
63 V
C14
10 k
48 V @ 5.2 A
R9
PI-2692-033001
1/02
G
RTN
23