BTS5210L_07 INFINEON [Infineon Technologies AG], BTS5210L_07 Datasheet

no-image

BTS5210L_07

Manufacturer Part Number
BTS5210L_07
Description
Smart High-Side Power Switch
Manufacturer
INFINEON [Infineon Technologies AG]
Datasheet
Data Sheet
• AEC qualified
• Green product (RoHS compliant)
Product Summary
1
Block Diagram
Smart High-Side Power Switch
Package
P-DSO-12
PG-DSO-12-9
V1.1, 2007-05-29
BTS5210L

Related parts for BTS5210L_07

BTS5210L_07 Summary of contents

Page 1

Product Summary • • • • • • • • • • • • • • • • • • • • • • • • • AEC qualified • Green product (RoHS compliant) Data Sheet Smart High-Side Power Switch ...

Page 2

Data Sheet control and protection circuit equivalent to channel 1 2 Smart High-Side Power Switch BTS5210L V1.1, 2007-05-29 ...

Page 3

Pin Definitions and Functions Pin Symbol Function 1 GND Ground of chip 2 IN1 Input 1,2 activates channel 1,2 in case of logic high signal 4 IN2 3 ST1 Diagnostic feedback 1 & channel 1,2 open drain, low ...

Page 4

Parameter Supply voltage (overvoltage protection see page 6) Supply voltage for full short circuit protection T = -40 ...+150°C j,start Load current (Short-circuit current, see page 6) ) Load dump protection 1 V LoadDump = 2 Ω ...

Page 5

Parameter and Conditions Thermal resistance junction - Case 6) junction – ambient cooling area Electrical Characteristics Parameter and Conditions -40...+150° unless otherwise specified j bb Load Switching Capabilities ...

Page 6

Parameter and Conditions, = -40...+150° unless otherwise specified j bb Operating Parameters Operating voltage ) Undervoltage switch off 9 ) Overvoltage protection Standby current ...

Page 7

Parameter and Conditions -40...+150° unless otherwise specified j bb Reverse Battery ) 16 Reverse battery voltage Drain-source diode voltage = - 2 +150° Diagnostic Characteristics Open load ...

Page 8

Truth Table ( each channel ) Normal operation Open load Overtemperature L = "Low" Level X = don't care H = "High" Level Status signal valid after the time delay shown in the timing diagrams Parallel switching of channel 1 ...

Page 9

Input circuit (ESD protection), The use of ESD zener diodes as voltage clamp at DC conditions is not recommended. Status output, ST1 or ST2 ESD-Zener diode: 6.1 V typ., max 0.3 mA 1.6 mA. The use of ESD ...

Page 10

GND disconnect with GND pull up Any kind of load > GND IN IN(T+) Due to V > low signal available. GND ST V disconnect with energized inductive bb load For ...

Page 11

Typ. on-state resistance high L R [mOhm] ON Typ. standby current , I 9...34 V, IN1,2 = low EE RII ...

Page 12

Timing diagrams All channels are symmetric and consequently the diagrams are valid for channel 1 to channel 4 Figure 1a: V turn on: bb Figure 2a: Switching a resistive load, turn-on/off time and slew rate definition: on Data Sheet Figure ...

Page 13

Figure 3b: Turn on into short circuit: shut down by overtemperature, restart by cooling (two parallel switched channels 1 and 2) ST1 and ST2 have to be configured as a 'Wired OR' function ST1/2 with a single pull-up resistor. Figure ...

Page 14

Package Outlines ø0.8 x 0.1 -0.05 1) Does not include plastic or metal protrusion of 0.15 max. per side 2) Stand OFF 3) Stand OUT 4) Pin 1 Index Marking; Polish finish All package corners max. R 0.25 Figure 1 ...

Page 15

Revision History Version Date Changes V1.1 2007-05-29 Creation of the green datasheet. First page : Adding the green logo and the AEC qualified Adding the bullet AEC qualified and the RoHS compliant features Package page Modification of the package to ...

Page 16

Edition 2007-05-29 Published by Infineon Technologies AG 81726 Munich, Germany Infineon Technologies AG 5/29/07. © All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics (“Beschaffenheitsgarantie”). ...

Related keywords