M30622MA-XXXFP RENESAS [Renesas Technology Corp], M30622MA-XXXFP Datasheet - Page 24

• Manufacturer Part Number: M30622MA-XXXFP
• Description: 16-BIT SINGLE-CHIP MICROCOMPUTER M16C FAMILY
• Manufacturer: RENESAS [Renesas Technology Corp]

Pin Description
Pin Description
X
AV
V
A
V
CNV
RESET
X
BYTE
AV
P0
D
P1
D
P2
A
A
A
P3
A
P4
CS
CC
IN
REF
0
0
8
OUT
0
8
0
8
Pin name
A
/D
, A
/D
A
0
0
0
0
0
CC
to A
SS
to A
0
to D
to D
to A
9
, V
16
to P0
to P1
to P2
to P3
to P4
0
SS
7
to CS
to A
1
,
A
/D
to
to A
SS
15
7
7
7
15
7
/D
0
/D
15
7
7
7
7
7
6
3
19
7
,
Reset input
Reference
voltage input
Power supply
input
CNV
Clock input
Clock output
External data
bus width
select input
Analog power
supply input
Analog power
supply input
I/O port P0
I/O port P1
I/O port P2
I/O port P3
I/O port P4
Signal name
SS
Input
Input
Input
Output
Input
Input
Output
Output
Output
Output
Output
Output
Input/output
Input/output
Input/output
Input/output
Input/output
Input/output
Input/output
Input/output
Input/output
Input/output
I/O type
Supply 2.7 to 5.5 V to the V
These pins are provided for the main clock generating circuit.Connect
a ceramic resonator or crystal between the X
use an externally derived clock, input it to the X
X
This pin is a power supply input for the A-D converter. Connect this
pin to V
This pin is a power supply input for the A-D converter. Connect this
pin to V
This is an 8-bit CMOS I/O port. It has an input/output port direction
register that allows the user to set each pin for input or output
individually. When used for input in single-chip mode, the port can be
set to have or not have a pull-up resistor in units of four bits by
software. In memory expansion and microprocessor modes, selection
of the internal pull-resistor is not available.
When set as a separate bus, these pins input and output data (D
This is an 8-bit I/O port equivalent to P0. Pins in this port also function
as external interrupt pins as selected by software.
This is an 8-bit I/O port equivalent to P0.
These pins output 8 low-order address bits (A
If the external bus is set as an 8-bit wide multiplexed bus, these pins
input and output data (D
(A
If the external bus is set as a 16-bit wide multiplexed bus, these pins
input and output data (D
in time by multiplexing. They also output address (A
This is an 8-bit I/O port equivalent to P0.
If the external bus is set as a 16-bit wide multiplexed bus, these pins
input and output data (D
by multiplexing. They also output address (A
This is an 8-bit I/O port equivalent to P0.
This pin switches between processor modes. Connect this pin to the
V
mode (memory expansion mode) or the V
operation in microprocessor mode.
A “L” on this input resets the microcomputer.
This pin selects the width of an external data bus. A 16-bit width is
selected when this input is “L”; an 8-bit width is selected when this
input is “H”. This input must be fixed to either “H” or “L”. Connect this
pin to the V
This pin is a reference voltage input for the A-D converter.
When set as a separate bus, these pins input and output data
These pins output 8 middle-order address bits (A
These pins output CS
select signals used to specify an access space. A
order address bits.
OUT
SS
0
–A
pin when after a reset you want to start operation in single-chip
pin open.
7
) separated in time by multiplexing.
CC
SS
.
.
SS
pin when not using external data bus.
0
–CS
0
0
7
–D
–D
) and output address (A
3
CC
7
6
signals and A
) and output 8 low-order address bits
) and output address (A
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
pin. Supply 0 V to the V
Function
CC
16
–A
IN
pin when starting
9
0
–A
–A
IN
19
and the X
8
15
8
7
. CS
pin and leave the
) separated in time
).
–A
16
).
Mitsubishi microcomputers
M16C / 62 Group
0
–A
1
15
).
–A
0
).
SS
19
–CS
7
OUT
) separated
are 4 high-
pin.
3
pins. To
are chip
(D
0
8
–D
–D
15
7
).
).
9